Home » Misc » How to make a homemade basketball return
How to make a homemade basketball return
The Best Basketball Return Systems of 2022
When I was a kid, I spent many hours shooting hoops in the driveway of my parent’s house. This driveway wasn’t exactly a regulation-sized basketball court: the front end of the sidewalk was our free-throw line, there were walls on each side of the narrow driveway, and the cobbled pavement was slanted significantly towards the street. Forget about working on your dribbling in these conditions!
But it turns out that the slanted driveway was a huge plus for working on my free throws. I could spend hours shooting the ball, and if I swished a shot the ball would automatically return to me. I only recognized this advantage later when I was shooting hoops on a perfectly even basketball court – rebounding my misses significantly reduced the number of shots I could get up in an hour!
That’s where basketball return systems come into play. They will rebound your made shots (and some will rebound your misses too) and help you to maximize the number of shot attempts you can take.
In this article, I am going to explain the differences between various types of basketball return machines and show you which one will work best for you.
The Best Basketball Return Machines:
Functionality: starstar_borderstar_border
Very affordable and quickly installed
The mechanism isn’t 100% reliable and doesn’t rebound misses
out of stock
Buy on Amazon
Functionality: starstarstar_border
Works on every basketball hoop
Rotation of the chute lets you pick the direction of rebounds
Price: $49.99
Buy from DICK's
+1 more store
Functionality: starstarstar_border
The net returns made shots and close misses
Doesn’t work if you shoot from the corner
Price: $99. 99
Buy on Amazon
Functionality: starstarstar_half
Receive rebounds in a more natural shooting position
Will rebound almost 100% of your shots
out of stock
Buy on Amazon
Functionality: starstarstar
By far the best ball return system under $1000
Rebounds 100% of your shots to where you want
Price: $599.99
Buy on Amazon
+1 more store
Amazon Prices were last updated on 10/29/2022 9:17 PM EDT
As you can see, there are many different types of basketball return machines on the market. But how do you find the perfect one for you? There are a couple of questions you should ask yourself:
Do you miss a lot of shots?
The most basic and affordable rebounding systems like the Spalding Back Atcha are attached to the bottom of the ring and only change the direction of basketballs that are actually falling through the net. – you still need to rebound misses yourself!
If you are making 90% of your free throws, this won’t pose much of a problem, but if you are still a beginner, rebounding systems like that won’t help you much.
More advanced basketball return nets will also rebound shots that bounce off the ring, but if you want a system that returns 100% of your shots you will need to invest in a more professional basketball return machine like the iC3 Basketball Shot Trainer .
Do you want to work on your corner three?
A lot of return systems will always return the basketball towards the free throw line no matter where you shot from. If you want to work on your corner three, that’s counterproductive as you need to run towards the middle of the court after every shot!
If you’re going to work on your bank shot take a look at the SKLZ Kick-Out 360 or the iC3 Basketball Shot Trainer that allow you to adjust the direction of the rebound.
The Top 5 Basketball Return Systems:
Spalding Back Atcha
The Spalding Back Atcha is probably the most affordable basketball return system on the market. It is made from thick plastic and comes with two hooks that attach to the back of the rim. If you make a shot, the basketball will hit the plastic structure after passing the net and will be kicked slightly towards the free-throw line.
out of stock
Buy on Amazon
as of 10/29/2022 9:17 PM EDT
The success rate of this mechanism varies somewhere between 50% – 95%, depending on the length and material of your net (nylon or metal?) and how well the plastic hooks attach to the hoop. However, don’t expect long shots to be returned all the way to the three-point line. Also, the rebound of the ball will always go towards the middle of the court which can be annoying if you are shooting from an angle.
Overall, the Spalding Back Atcha is a very affordable basketball return system that you can attach to most hoops within seconds. While it doesn’t do a perfect job of returning made shots and won’t return misses at all, it will still allow you to save a lot of time. Chasing down the rebound after every second shot is still much better than running every time!
The SKLZ 360 works very similarly to the Spalding Back Atcha presented before, but the mechanism is a bit more complex and versatile.
The installation is pretty simple: If you own an height-adjustable basketball hoop you just lower the hoop and clip the four hooks to the rim. Otherwise, you will probably need a small ladder unless you’re 7ft tall.
Price: $49.99
Buy from DICK's
+1 more store
The chute of the SKLZ 360 hangs about 28 inches below the rim and does a great job of returning the ball. The best feature of this chute is the fact that you can rotate it by 360 degrees! This way you can get the basketball returned no matter where you are shooting from. Small kids will not be able to do this on a 10ft hoop, but anybody taller than 5’8″ should be able to do it without a ladder or lowering the hoop.
The quality of the SKLZ 360 is a lot better than the Spalding Back Atcha, but some people still report that the chute might change direction on its own and that the plastic hooks won’t last forever. However, you should be able to fix these issues with a little bit of duct tape and metal wire ties.
Overall, this is a basketball return system with much-improved functionality that I can recommend if you are looking for something you can attach and detach easily. The only downside: it doesn’t rebound missed shots.
Goaliath Basketball Return Net
Goaliath is known for producing high-quality in-ground basketball hoops but they also sell accessories that make the life of basketball players easier.
This basketball return system is the first in this article that can rebound missed shots too. That’s especially useful for beginners who are still missing a majority of their attempts.
Price: $99. 99
Buy on Amazon
as of 10/29/2022 9:17 PM EDT
The installation is pretty simple: You attach the webbing harness to the metal bar at the top of the net and pull this harness over the back of the rim. On the other side, the net is attached to two bags that you can fill with water or sand.
The Goaliath return net especially well if you want to prevent the ball from going into the neighbor’s yard or a thorny bush of roses. However, if you are looking for a system that will replace your buddy passing you the ball while you are moving along the 3-point line, then you better keep looking.
SKLZ Rapid Fire II
The SKLZ Rapid Fire II is comparable to the Goaliath net but comes with one significant difference: the net is attached to two hip height stands. This small change is fantastic because you no longer have to bend down to collect rebounds. Instead, you receive the ball in a much more natural shooting position.
out of stock
Buy on Amazon
as of 10/29/2022 9:17 PM EDT
This ball return system easily attaches to the top-left and top-right corner of any metal frame backboard, unfortunately, it won’t work for molded backboards. The net is held by two adjustable metal arms that extend from the top of the backboard. By placing the stands differently and rotating the arms of the net, you can direct the rebounds to different spots on the court. You can also use the net as a ball stop by fully folding back the arms.
Overall, the SKLZ Rapid Fire is a very versatile basketball rebounding system that allows you to get shots up at a much higher frequency because you receive the basketball in a position that comes close to a regular pass in a game.
iC3 Basketball Shot Trainer
The iC3 Basketball Shot Trainer plays in a different league than all the other rebounding systems presented so far. It’s an affordable entry-level model by Dr. Dish Basketball, a well-known company that also builds basketball passing machines that cost thousands of dollars and are used by professional basketball players.
The iC3 is made of a sturdy steel frame that you hang over the back end of the rim and fix to the pole of your basketball hoop. If your basketball hoop doesn’t have a pole, you can still use the iC3 if your backboard is at least 60 inches wide.
Price: $599.99
Buy on Amazon
as of 10/29/2022 9:17 PM EDT
+1 more store
The net stretches over the rim and catches almost every missed shot. This design also forces you to shoot with a proper arc and actually improves your technique. The net funnels the ball into a small ramp that you can rotate by 180 degrees to receive rebounds in every position on the court. The rebounding system is not very fast, but if you use two basketballs you can shoot nonstop rapid-fire style!
The iC3 Basketball Shot trainer is by far the most professional rebounding system that is still affordable and doesn’t cost thousands of dollars. If you are an ambitious basketball player and you want to work on your shot, then this is the system to get!
Conclusion
I recommend you to go for the iC3 Basketball Shot Trainer . It’s the most expensive system in this roundup, but also by far the best! It rebounds almost 100% of your shots, you can change the direction of the rebounds, and it even forces you to improve the arc of your shot!
If you are looking for a cheaper option and you are a pretty good shooter, then the SKLZ 360 is a good option too.
If your kids are learning to play basketball in the driveway and you want to prevent the ball from bouncing into the neighbor’s garden then check out the Goaliath Basketball Return Net .
STEAM@Home: Make Your Own Basketball Hoop!
No application or registration needed.
Location
Only virtual (online or over the phone).
Find an area where you can lay out materials and do some hands-on construction.
Additional information
Materials:
A wire hanger. It cannot be a partially metal hanger made substantially of wood or plastic.
A large, flat piece of cardboard.
The tape of your choosing. Masking tape may be the easiest to work with; duct tape would certainly make the hoop durable.
Markers or paint.
Scissors.
String (optional).
Instructions:
Bend the wire hanger into a circle. You do not even have to dismantle the hanger, but just reshape it into a hoop.
Bend the hook of the hanger so that it is at a 90 degree angle with the hoop. Do not cut away the hook, as it still can be of some use.
Cut the cardboard to the size and shape of your liking. Standard high school, college, and NBA backboards are rectangular, if you are looking to replicate that appearance. Try to make sure the relative scale of the hoop and backboard seem reasonable. For comparative purposes, an NBA backboard is 6 feet wide, while the basket opening is 18 inches (1.5 feet). That means the basket width is 1/4 (or 25%) as wide.
Decorate the hoop and backboard to your liking. Traditional hoops are painted red, but you can certainly customize it to fit whatever you desire. The backboard of most high schools, colleges, and all NBA franchises are now made of transparent glass; as there is no transparent cardboard, you can really be as creative as you want.
Tape the hoop to the backboard. You can attach the hook (which you bent up earlier) to lower back side of the backboard. Make sure the rim is as close to the backboard as possible.
Attach a net to the basketball rim (optional). You can make make a net out of string, or even out of twisted tape.
Hang the completed basket to a wall or door. Masking tape will work well for this purpose, as it will not leave a sticky mess behind like duct tape would. There are two different taping methods you can employ.
This activity supports the practice of these STEAM Habits of Mind: Develop craft, engage & persist, observe, reflect, stretch & explore.
Tips for Supporting Your Children's Learning
Get your child actively involved in their own learning and having their questions drive the learning. Let them observe and figure out, and try to hold back from answering questions for them. Instead, try to ask: What do we know? What else can we find out? How might we figure that out? Don't be afraid to ask your child questions. Also, don't be afraid to say "I don't know--let's find out together!" as a way to respond to their questions. Here's an article to help you support this kind of learning: Of the Value of Saying I Don’t Know
Want to learn more about making your own sports equipment?
Science Club for Girls at Home - Make you own sports equipment challenge
Instructables - MYO Basketball hoops
More hands on activities and learning opportunities:
Homecourt - basketball skill building app
Cambridge Public Schools Virtual Enrichment Recommendations
Exploratorium - Sports Science
Design Squad - Sports design challenges
Parkour Generations - Classes
Department of Human Services Sports Leagues
More STEAM@Home suggestions!
MIT Full STEAM Ahead
STEAM Habits of Mind - observe, reflect, engage & persist, stretch & explore, imagine, develop craft
How to make a do-it-yourself basketball shield ring?
Useful crafts
Hello do-it-yourselfers! Ball games are one of the most favorite among children, and in order to somehow diversify this activity, especially since kindergartens are not working now, I decided to make a simple shield with a basketball hoop. Making such a shield with a ring with your own hands is very simple. You just need to follow the step by step photos and repeat. And by the way, he literally did everything from trash, from scraps of metal to boards.
So let's get started! We will need:
some kind of ring (cut off from the gas cylinder stand)
two pieces of profile (one 4*2, the second 2*2)
two pieces of reinforcement
cutting boards (shield size 60*80)
First of all, we prepare the ring itself. For its manufacture, I took the base from a gas cylinder, marked a strip on it and sawed it off with a grinder.
Before cleaning the ring from rust and old paint, I drilled 12 holes in a circle at the same distance in order to pass the mesh through these holes in the future.
Further, as I wrote above, trimmings from the profile pipe will be needed. I don’t give sizes, since everything was done by eye, but if you suddenly decide to repeat it, write about it in the comments and I will measure everything and write to you.
Now all these components need to be welded into a single structure. Everything is done very simply and you can see the whole final result in the photo below. The only thing I needed was to add more crossbars to the main long crossbar, so that the structure on the shield would hold tighter, but as practice has already shown, everything holds up well too.
Next, you need to make a shield. To do this, he dissolved the trimmings of the board into components. My board was 10 cm wide. For an even cut, I used trimming, and also processed the front parts of the boards with a grinding wheel.
Then I fastened all the boards together with battens. The reverse side of the shield was not polished.
To add beauty and weather protection, I impregnated the shield with a special impregnation in the color of mahogany.
Then, when the impregnation dried, I fixed the ring on strong, yellow self-tapping screws. I used 4 self-tapping screws and, as practice has already shown, this is quite enough. Also installed a special grid. I bought such a grid on Aliexpress, if you need one, then here is the LINK: BUY NET FOR RING
And now you can install this shield on the street. So far, I have temporarily fixed it on the Swedish wall (in the future I will flood the pole and hang a shield on it).
And here is the first goal scored! Everything turned out just fine! The children were just delighted with this homemade product! And the joy of children is the most important thing!
I also recommend you watch a very addictive ASMR video on how to make this basketball hoop.
If this article was useful to you, then support it with a like! Thank you all for your attention and see you soon!
Tagsdiybasketball courtdiybasketball hoop at homehow to make a basketball hoophelpful tipshelpful tips videohelpful tips for homehelpful tips for repairinghomemadehomemadediy diydiy homemade diy at homehomemade basketball hoopdiy diymasters secretstipstricks of masters
Do-it-yourself basketball backboard with height adjustment (20 photos).
Basketball backboard dimensions and markings
Today we will talk about how to make a high-quality basketball backboard and basketball net with your own hands at home from improvised materials. We will also consider the technology of manufacturing a basketball backboard and a net for playing basketball for children or adults.
In order to make a simple DIY basketball hoop for kids, we need thick wire and rope. Instead of thick wire, you can take an old unused hula hoop, cut it, shorten it and reconnect it. It is important to leave a "sprout" for attaching the ring to the shield.
If you want to make a basketball hoop with your own hands from thick wire, then in order to get the most even circle, we recommend using a cylindrical fixture designed to serve as a template. We wind the wire around it. And do not forget to leave a "sprout" for attaching the resulting ring to the basketball backboard.
The diameter of the metal blank for the ring should be slightly larger than the diameter of the basketball. Then you should take the prepared rope and cut it into 20-22 identical segments. At the same time, the length of each should be 2.5 - 3 times greater than the planned length of the mesh hanging.
These pieces are attached to the metal ring at regular intervals. You need to tie the ropes exactly in the middle so that 2 ends of equal length remain free. Then we connect in turn 2 ends of nearby ropes around the entire circumference of the ring. This is the first level of our grid. Then, similarly, we tie the ropes to the next level, etc. If you want to make a basketball hoop for your home, you can tie the bottom of the net so that the ball will stay inside when it hits. This will help reduce the chance of an accidental bounce of the sports equipment after hitting the basket.
DIY basketball backboard for adults. How to make a professional basketball backboard - here you have to try. How to make a basketball backboard at home. The process of making a basketball backboard is no more difficult than making sports predictions, especially if the necessary materials are available.
Here is a typical instruction for making a basketball backboard at home. For the base of the basketball backboard, you can choose a sheet of plywood, which is inexpensive and not hard to get either. A sturdy rectangular piece of plexiglass or thick plastic may also work well.
If the basketball backboard will be installed outdoors, then it is worth choosing the material for its base based on considerations not only of strength, but also of resistance to adverse weather conditions.
The next step is to choose a place where the basketball backboard will be attached. When choosing such a place, the main thing to remember is that the lower edge of the shield should be at a height of 290 centimeters from the ground, and the ring should be located at a height of 305 centimeters.
Now you need to mark and cut out the dimensions of the plywood blank. The ideal size of a standard basketball backboard are the following parameters: width - 1.8 meters, height - 1. 05 meters. This size will allow players to make more accurate and varied throws.
Before you start cutting out the workpiece, you need to use a pencil to outline the dimensions and draw lines along which the workpiece will be cut. It is better to cut it with a jigsaw, when working with which you must be careful.
After the blank of the future basketball backboard is ready, it will be necessary to draw a white square on it, which plays a very important role.
The white square is a kind of guide for the players when shooting, with the help of such markings it is much easier to get the ball into the basket. If the ball is correctly thrown into the corner of this square, then it will definitely reach the goal.
In order to mark out such a square, not only a brush and paint are needed, but also knowledge of the dimensions of the rectangle. Its external dimensions are 59 centimeters horizontally and 45 centimeters vertically.
When marking out, it should also be taken into account that the upper edge of the base of this rectangle must coincide with the level of the upper plane of the ring. The width of the stripes of the square should be 5 centimeters.
Basketball hoops
Material - solid steel, inner diameter 45 cm and painted orange. The metal bar of the ring must have a minimum diameter of 16 mm and a maximum diameter of 20 mm. On the bottom of the ring there must be devices for attaching nets, such as to prevent injury to the fingers. The mesh must be attached to the ring at twelve equally spaced points along the entire perimeter of the ring. Net attachment devices must not have sharp edges or crevices that could get caught by the player's fingers.
The ring is attached to the structure supporting the basket so that no force applied to the ring is transmitted directly to the backboard. Therefore, there should be no direct contact between the ring and the device that secures the ring to the shield and the shield. However, the gap must be small enough that fingers cannot get into it. The top edge of each ring must be located horizontally at a height of 3. 05 m above the ground at an equal distance from the vertical edges of the board. The nearest point on the inside of the ring must be 15 cm from the face of the shield. You can use rings with a shock absorber.
Made of white cord and designed to hold the ball momentarily as it passes through the basket. The net length must be at least 40 cm and not more than 45 cm.
Each net must have 12 loops to attach to the ring. The top sections of the net must be sufficiently rigid to prevent: The net will wrap around the ring and become tangled. Ball stuck in the net or thrown out of the net by the net. Basketball net can be woven from braid, twine, rope, thick threads. The braid or thread is first cut into segments.
The length of each segment must be four times the length of the grid. The number of segments is determined as follows: the ring intended for the grid is measured, and the resulting value is divided by four. The do-it-yourself basketball backboard is almost ready. Now it needs to be firmly fixed. To do this, you will need 4 large bolts that can withstand a load of 30 kg, and drill four holes in the wall or any other place where the basketball backboard will be mounted.
Use a spirit level to drill holes evenly. After that, you can start installing the shield. It is very inconvenient to do it yourself, so you should again resort to the help of friends who can insure you on the stairs, as well as file and hold the shield.
Once the bolts are installed and screwed into place, the basket can be hung up so that you can finally play on the court with a new basketball backboard that will last for many years.
In short, you can make a good basketball backboard with your own hands. But it is important to pay attention to one serious point.
The fact is that no matter how it seems to us from the side that the contact of the ball and the basket hoop is quite soft, it should be noted that the impact load on the fastening of the hoop to the backboard is very high. The weight of the ball (if you do not go into the definition of physical values) during contact with the ring increases many times, even when thrown from an average distance.
Well, with an inaccurate hit from a long distance, this blow can reach destructive power. And such a load acts on the mount hundreds and thousands of times. So that your work does not go to waste, that is, the future ring with a shield is a reliable design, you need to pay maximum attention to attaching the ring to the shield and then the same shield to the wall or other structure. Regarding the material of the shield, it can be put together from the same inexpensive pine boards available, and preferably from harder wood. Proposals to make a basketball backboard from plywood, fiberboard, plastic do not stand up to criticism. The first two positions do not pass due to the fact that if your shield hangs in the season in the rain and the sun, nothing will remain of it.
Plastic will naturally withstand all of these weather conditions, but is unlikely to be affordable. Plastic plastic is different, because the one that is used in the gym is very expensive, another different lottery ... will stand it - will not stand it. But a wooden board, it is a material that has stood the test of time and history. It is known that the official dimensions of the basketball backboard are as follows - a width of 1 meter 80 centimeters and a height of 1 meter 5 centimeters.
But in principle, you can try to build a flat square of boards 3 cm thick and 80 cm x 80 cm in size, I think this area will be quite enough to play normally or work out the throw. Basically, only a square is actively used when throwing (its dimensions are 59centimeters, height 45 centimeters) above the hoop, since this is the small square you need to be able to hit if you want to perform a throw from the shield.
Then (if it hits this square), the ball will most likely fall into the ring. Even in this case, if you perform a throw with a rebound from the shield, the load on the shield itself will be very small, but on the fastening of the shield and the ring, in this case, the pressure will be maximum.
Basketball hoop is made from a metal rod with a diameter of 16 - 20 millimeters. I think everyone understands that in order to protect against atmospheric precipitation, the entire structure should be painted with the appropriate paint, which can be bought at the store, explaining to the seller why the paint is needed.
As a result, I will repeat myself and say that when trying to make a basketball backboard on your own, pay attention to the fastening of the ring to the backboard. This is the most fragile place in this design.
In this article you will learn:
What are the dimensions of the basketball hoop
How to make a basketball hoop with your own hands
Where to buy a ready-made basketball backboard with a ring
Basketball-like games were found among the ancient Scandinavian peoples and Mexican Indians. Today in northern Mexico, one of these games is popular - "Pok-Ta-Pok". It is believed that it appeared due to religious rites, which eventually turned into sports fun and an attraction for tourists. How the game "basketball" appeared, and what is a basketball backboard with a ring as a necessary element of this popular game, we will learn in this article.
When basketball and the first backboard with a hoop appeared
The forerunner of basketball is the 19th century children's game "duck on the rock", familiar to the Canadian inventor of basketball, James Naismith. The principle of the game was to hit a small stone on top of a large one.
The concept of basketball was finally formed when D. Naismith moved to the USA and became a physical education teacher at the Youth Christian Organization College (YMCA) in Springfield, Massachusetts. Already teaching physical education and as a college professor, he faced the challenge of creating a winter game between baseball and football. Naismith, given the weather conditions this time of year in Massachusetts, decided that this game should be played indoors.
Naismith's goal was to create an outdoor game for the students of the Christian Workers' School that required more than just strength and dexterity. It was supposed to develop coordination of movements in teenagers and at the same time be interesting.
So, in the winter of 1891, under the leadership of Naismith, the first basketball baskets were installed in the college gym. Baskets from under the fruit, fixed on both sides of the hall on the balconies, which encircled the room around the perimeter, acted as basketball hoops. Such baskets were fastened at a height of 3.05 m, it was this indicator that became the international standard, which is observed to this day.
The task of the players was to throw the ball (at that time they used football) into the basket. The first basketball match was held in the same hall on December 21, 1891. According to the conditions of the game proposed by Naismith, each team had 9 people, which exactly coincided with the number of students in the group.
The news of the new game quickly spread throughout America, and Naismith was asked to send the rules. On February 12, 1892, after learning the rules and mastering the basics of technology, the students of Springfield College played the first "official" match in the history of basketball, which ended in a 2-2 draw.
This meeting turned out to be so successful, and the rumor about a new type of competition spread so quickly that soon two Springfield teams began to hold demonstration competitions, which were already attended by hundreds of spectators. The initiative was picked up by students from other educational institutions, and the following year, the Northeast of America was swept by a real basketball fever.
The rules of basketball that Naismith wrote himself as a college instructor at 1891 year, was a list of 13 points, which eventually formed the basis of modern international rules, which hardly fit on 200 pages. In 1893, instead of baskets, they put iron rings with a grid, two years later they added shields, and two years later the team was reduced to 5 people.
What is a basketball backboard with a ring today? The shield is made of a transparent material, usually a single piece of tempered impact-resistant glass with a degree of hardness corresponding to that of a 30 mm thick hardwood shield.
It is allowed to produce such shields from other materials, but in this case they must be painted white and comply with other requirements for such sports equipment.
The front side of the shield is made smooth, a marking line is applied along the edges, a rectangle measuring 45 cm vertically and 59 cm horizontally is indicated at the place where the ring is attached. Moreover, the upper edge of the base of the rectangle must coincide with the level of the upper plane of the ring. White outlines are applied to transparent shields, and black is used in other cases. The width of the lines is 5 cm.
The basketball backboard with hoop is installed at right angles on both sides of the playing court, parallel to the front lines. The center of the front surface of each shield lies on perpendicular lines reconstructed from points located on the site at a distance of 120 cm from the middle of the inner edge of each front line.
Shields are upholstered, the following requirements apply to it:
the sides of the boards and the bottom end are covered with soft material at a height of at least 35 cm from the bottom corners;
the lower end is upholstered with material at least 5 cm thick;
the rear and front surfaces of the shield should be decorated with upholstery material, the thickness of which is at least 2 cm, at a height of at least 2 cm from the bottom end.
The following requirements are imposed on the structures on which the shields are attached: their front parts, including the upholstery, are placed at a distance of at least two meters from the outer edge of the front line. They are painted in bright colors that contrast with the walls of the sports hall in order to provide sufficient visibility to the players of both teams.
The structure on which the basketball backboard with the hoop is mounted is fixed to the floor of the court in such a way as to prevent it from moving during the game.
Structures used for fastening the shields must be upholstered with soft material behind the shield at a distance of 120 cm from the front surface of the shield. The minimum thickness of the upholstery is 5 cm, and the density is the same as that of the upholstery of the shields.
The base of the structure from the side of the playground is upholstered with dense soft material to a height of at least 215 cm, the thickness of the upholstery is 10 cm.
The minimum value of the so-called "indentation factor" of the upholstery of panels and structures is 50%. This figure means that when an appropriate force is applied to the upholstery, its indentation should be within 50% of its original thickness. The upholstery material provides protection to players from possible injuries during the game.
Basketball backboard and hoop dimensions
It's hard to imagine a basketball court without a basketball backboard and hoop. For them, world standards established by the International Basketball Federation have been adopted.
A basketball backboard is a rectangular or square panel to which a hoop is attached. Mounting is provided on the shield for mounting on a pole or hanging on a wall: rigid mounting is required, the product should not stagger and move.
Shield dimensions - 1.8x1.05 meters, with an installation height of 2.9 meters. By NBA standards, the size of the backboard must be 72x42 inches. Two shields are installed opposite each other from different ends of the field, the material is impact-resistant (as an option, tempered glass, acrylic, wood). Lines are drawn on a smooth surface. Models of basketball backboards with a net that are not intended for stationary installation are equipped with the same mounting elements as in the brackets for hanging punching bags. This method makes basketball backboards able to withstand a lot of weight and securely fixes them.
Ring or basket includes a metal (steel) circle covered with netting without a bottom. It is installed at a height of 3.05 meters from the floor and indented 15 cm from the lower edge of the shield. The inner diameter is selected from the range of 45–45.7 cm. The basketball hoop is painted in a bright color, usually orange. It is impossible to allow the transfer of load from the basket to the shield, therefore, the installation of the product is carried out with special attention.
DIY basketball hoop
Homemade basketball hoops are installed in summer cottages or hung in the yard near the house. In the summer, you can throw the ball with pleasure, feeling like Michael Jordan for a moment. This game is available to everyone: both children and adults. The benefits of such a seemingly simple exercise are incredible!
Have you set out to make your own basketball hoop and don't know where to start? Further, we will talk about this.
To make your own basketball hoop, you need thick wire and rope. Instead of a wire, an old unnecessary sports hoop is suitable, which is cut, shortened and connected again. Do not forget to leave a "sprout" for attaching to the shield.
Making a thick wire basketball hoop requires some trickery. To obtain an even circle, a cylindrical fixture can be used as a template on which the wire is wound. But, before cutting off the wire, do not forget about the "sprout" for attaching to the wall.
The diameter of the metal blank for the hoop is slightly larger than the diameter of a basketball. Next, the pre-prepared rope is cut into 20–22 identical segments. The length of each is 2.5–3 times the planned length of the net hanging.
These segments are attached to the metal ring at regular intervals. The ropes are tied in the middle, and the two ends of equal length are left free. Then the two ends of the nearby ropes are tied in turn, and so on along the entire circumference of the ring. It turns out the first level of the grid. The ropes of the next level are tied in the same way, and so on.
When making a basketball hoop for the home, the bottom of the net can be tied, which will allow the ball that hits the net to stay inside. Thus, the ball does not accidentally bounce to the side.
Now we know how to make our own basketball hoop. But it is necessary to answer the question, which is better - a home-made or a quality product bought in a store?
Making your own parts is fun. To do this, you only need free time, the necessary materials and a third-class welder. If you do not have this, then it is better to purchase a basketball hoop with a backboard from trusted manufacturers.
In order to make a basketball backboard with fastening, you will need six meters of a 2x2 cm profile pipe, 8.5 m of a 2x4 cm profile pipe, a backboard made of laminated moisture-resistant plywood, a basketball hoop, six anchor bolts for attaching to the wall. The design is assembled from three parts for easy wall mounting.
The desired part is cut off from the shield.
Metal structures are welded and the prepared AKZ is applied to them.
The shield is drawn, pasted over with adhesive tape, and lines 5 cm wide are applied to it.
Attach the shield to the frame.
Where to buy a basketball hoop with a backboard
In such an active game as basketball, every little thing is important! Even at the finish line, troubles happen: the ball is in the ring, but gets tangled in the net and gets stuck. This moment is ruined! How to avoid such troubles?
The following requirements apply to the ring net:
12 fastening loops;
length should be 40–45 cm;
use rigid white cord as material;
upper is made in such a way as to prevent throwing the net on the ring, tangling or sticking the ball.
How to choose the right basketball net? The main thing to pay attention to is the material, diameter and thickness of the thread, type.
Capron and nylon products are used more often. The latter is more wear-resistant, so for professional training, boron falls on this material.
The diameter is selected according to the diameter of the ring and the ball.
For professional basketball nets, thick threads of increased strength are used, but for amateurs, more fragile ones can be used.
Type: knotted and knotless. Products of the first type are widely used, but knotless basketball nets for the hoop look better and absorb the impact of the ball well, and are more reliable.
Looking for quality hoop backboards? We will help you make the right choice. Sportstyle started its activity in 1992 and has been successfully presenting its goods and services in the markets of Russia and neighboring countries for more than 20 years.
One of the main activities of the company is the production of sports equipment. Our products are very popular and in demand, among them:
boxes, rings, bags and pears;
wrestling mats;
equipment for sports aerobics and much more.
The range of our company is not limited to sports equipment. We are happy to produce for you tents for summer cafes and weddings, awning garages, trade tents, awnings for cars and boats, as well as pool bowls.
Our son became interested in basketball in the summer, and although there is a beautiful stadium with a basketball court half a kilometer from home, sometimes you want to knock the ball near the house. Therefore, it was decided to make a do-it-yourself basketball backboard near the fence (so that you could knock on a relatively hard road surface, and the ball would fly away, if it didn’t hit the ring, to our site, and not to someone else’s. We deviated a little from the standard and we got the following dimensions (photo is clickable)
The shield was cut out of OSB (just in case, two layers were twisted, and one more, a small square, was added to strengthen the fastening - this can be seen in the photo below) and carefully painted with oil paint
The support was made of metal profiles 50*50 and 56*56 in size. The fact is that that part of the fence, at which the shield is attached, is supposed to be removable for us - it is there that we usually dump soil, crushed stone and other minerals. Therefore, it was decided to make the shield removable. Along with support. We implemented this idea like this.
A short post driven into a previously dug hole and cemented. The long one is fixed in it with screws. If necessary, it can be taken out. Actually, this is also visible in the diagram above.
Just before the shield was built, we had a welding machine, and this product proved to be a great workout. The pipes were welded with the letter G, a beautiful rectangle was welded to a short crossbar, on which a shield was attached.
Mesh rings are sold for little money in all sports shops and in many hyper stores. It turned out very nice.
Oh sport, you are the world!
There is nothing to do in the country, only bending metal, fumbling shish kebab, drinking beer. It is necessary to go in for sports both by ourselves and by children.
True, for this you will first have to "bend the metal" and celebrate this matter with beer and barbecue.
Basketball backboard in the next series of the "Made of Metal" project. Joint work of me and my father.
Batko studied the standards for the height and dimensions of a basketball backboard, made a wooden backboard, painted it, made wing screws, installed a pole. Well, in addition, he made critical remarks to the metal part.
I - designed the whole metal part and welded the metal.
Let's go!
01. First I sit down at the computer and sketch out the drawing of the shield and the pole itself.
The original plan was to put the ring in another place and pull it with a solid hitch to the nearest tree. But there turned out to be a lot of roots and they decided to put them in free flight and without a screed, which is why the ring in the upper part of the column remained rudimentary only in the drawing. Diagonals that are not in the drawing (green) have also been cancelled. We decided that the rigidity of the wooden shield and metal fasteners would be enough not to "walk".
Also on the move I changed the way of strengthening the outrigger knee. Not with a corner as in the drawing, but with two stripes on the sides, see the photo below.
A 5 cm profile was used for the pole, a 6 cm profile was used for the bracket strung on the pole. A strip is welded inside to prevent play. Everything that adjoins the wooden shield is a 25 mm corner.
Important: the ring must be universal for both adults and children of different heights. Therefore, a height offset system was made.
02. The main large elements are welded: a pole, a knee, two stepson solid fuel boosters. The upper edge of the pillar and stepchildren is bevelled: for rainfall and for beauty.
03. More different types
04.
05. There is a strip welded inside the elbow pipe. At the top of the hole.
06. Welded shield fixing system. No, this is not a bottle of Zhatetsky Gus beer, this is gasoline.
07. Stepsons welded on. There was an error in the calculations. It was assumed that the stepchildren would strengthen the pillar from swinging, but they were attached lower than necessary. Further in the photo you will see that they protrude quite a bit from the ground. It would be possible to raise 30-40 cm higher. And now, nevertheless, the pillar sways during the game.
08. The heels are welded to the part that goes underground.
09.
10. Everything is painted
11.
12. Pit
13. It will be found so for a couple of days and you can continue the part of the pillar, because there was no putty for metal, to putty the seams. The putty was bought in addition, puttied and repainted a little later.
14. Up!
15. Shield assembly.
16. Done!
17. Now the ring is at its lowest height. Even lower than calculated, because one hole is not used (see the vacant thumb screw). Altitude change occurs with the help of one man-power on a stepladder.
18.
19. The village basketball open championship has begun!
Did you have to restrain yourself when you passed the basketball court in order not to throw the ball into the basket? Why hold back? Team sports reliably unite people of any age, religion and social status. And in order to look decent at any moment and on any site, it is enough just not to start training.
Small places for playing streetball can be equipped on sports grounds near the house, and rings can be built at summer cottages for children to play from improvised means. So, how to make a basketball hoop yourself?
Dimensions and materials required
The inner diameter of the basketball hoop is 45 cm;
the height of its upper edge above the playground is 3. 05 m;
ring material - metal bar, plastic pipe, improvised materials;
diameter of a bar or pipe for a ring - 16-20 mm;
distance from the ring to the shield - 15 cm;
mesh length - 40-45 cm;
mesh material - metal chain, synthetic cord, rope, braid.
Types of basketball hoops
Hoops can be different:
metal with anti-vandal nets made of metal chain;
metal with rope mesh;
plastic with nets of various types of materials;
creative (from the remains of construction, from old furniture, from large plastic containers).
The construction of a metal bar ring begins with marking. Since the basket must have an internal diameter of 45 cm, a rod or pipe is selected based on this.
Material length is calculated using the formula:
Bar length = Circumference diameter x 3.14 (pi value). We have 45 × 3.14 = 141.3 cm.
Since we need to fasten the ring to the shield, let's take the length of the rod about 150 cm.
99
– you still need to rebound misses yourself!
It is made from thick plastic and comes with two hooks that attach to the back of the rim. If you make a shot, the basketball will hit the plastic structure after passing the net and will be kicked slightly towards the free-throw line.
Chasing down the rebound after every second shot is still much better than running every time!
99
It’s an affordable entry-level model by Dr. Dish Basketball, a well-known company that also builds basketball passing machines that cost thousands of dollars and are used by professional basketball players.
If you are an ambitious basketball player and you want to work on your shot, then this is the system to get!
For comparative purposes, an NBA backboard is 6 feet wide, while the basket opening is 18 inches (1.5 feet). That means the basket width is 1/4 (or 25%) as wide.
There are two different taping methods you can employ.
Making such a shield with a ring with your own hands is very simple. You just need to follow the step by step photos and repeat. And by the way, he literally did everything from trash, from scraps of metal to boards. 
I used 4 self-tapping screws and, as practice has already shown, this is quite enough. Also installed a special grid. I bought such a grid on Aliexpress, if you need one, then here is the LINK: BUY NET FOR RING 
Basketball backboard dimensions and markings 
Then you should take the prepared rope and cut it into 20-22 identical segments. At the same time, the length of each should be 2.5 - 3 times greater than the planned length of the mesh hanging. 
05 meters. This size will allow players to make more accurate and varied throws. 
The width of the stripes of the square should be 5 centimeters. 
05 m above the ground at an equal distance from the vertical edges of the board. 
Now it needs to be firmly fixed. To do this, you will need 4 large bolts that can withstand a load of 30 kg, and drill four holes in the wall or any other place where the basketball backboard will be mounted. 
The weight of the ball (if you do not go into the definition of physical values) during contact with the ring increases many times, even when thrown from an average distance. 
Plastic plastic is different, because the one that is used in the gym is very expensive, another different lottery ... will stand it - will not stand it. But a wooden board, it is a material that has stood the test of time and history. It is known that the official dimensions of the basketball backboard are as follows - a width of 1 meter 80 centimeters and a height of 1 meter 5 centimeters. 
How the game "basketball" appeared, and what is a basketball backboard with a ring as a necessary element of this popular game, we will learn in this article. 
It was supposed to develop coordination of movements in teenagers and at the same time be interesting. 
It is allowed to produce such shields from other materials, but in this case they must be painted white and comply with other requirements for such sports equipment. 
Two shields are installed opposite each other from different ends of the field, the material is impact-resistant (as an option, tempered glass, acrylic, wood). Lines are drawn on a smooth surface. Models of basketball backboards with a net that are not intended for stationary installation are equipped with the same mounting elements as in the brackets for hanging punching bags. This method makes basketball backboards able to withstand a lot of weight and securely fixes them. 
In the summer, you can throw the ball with pleasure, feeling like Michael Jordan for a moment. This game is available to everyone: both children and adults. The benefits of such a seemingly simple exercise are incredible! 
The length of each is 2.5–3 times the planned length of the net hanging. 
Diagonals that are not in the drawing (green) have also been cancelled. We decided that the rigidity of the wooden shield and metal fasteners would be enough not to "walk". 
At the top of the hole. 
05 m; 
