We are reader-supported. When you buy through links on our site, we may earn an affiliate commission. Learn more
by Sportszpro
If you just bought a portable basketball hoop, you probably know that you will need to fill it up with sand to make it stationary. But how much sand do you need to use?
Well, this guide will tell you all about how much sand for basketball hoop base you need. Here is the good news, figuring it out is pretty easy and we will give you a short and easy-to-follow step-by-step guide on how to fill your hoop. So, let's get started.
Table of Contents
Why Sand for Your Basketball Hoop?
Reason 1: Sand is Denser
Reason 2: Water Can Freeze
How Much Sand for Basketball Hoop Base Do You Need?
How To Fill Sand In Your Basketball Hoop?
Wrapping Up
Why Sand for Your Basketball Hoop?
You actually don't have to choose only sand for your basketball hoop. There are other things you can use to weigh it down like water. However, sand is the better option. Here is why.
Reason 1: Sand is Denser
Compared to water, sand is about 45% denser. That means with sand, your brand-new portable basketball hoop will be much more stable. With a portable basketball hoop, stability is one of your main concerns. So, using sand instead of water is the better choice.
Reason 2: Water Can Freeze
Another very important reason why you might want to go with sand instead of water is that water can freeze up. This can especially be a problem if you happen to live in a very cold climate.
If the water is frozen, the hoop will become much heavier and it may be damaged. With sand for a basketball hoop, you won’t have any freezing problems, whatsoever. Also, the opposite is true. In very hot climates, water may evaporate. That’s another thing you don’t need to worry about with sand.
How Much Sand for Basketball Hoop Base Do You Need?
Alright, let’s get into it then. The thing you need to know is most portable basketball hoops in the market will have a 35-gallon water capacity. This can be different for other models, but 35-gallons based hoop is pretty standard.
To substitute 35-gallons of water, 500 LBS of sand would do just fine. Just go to any home store and buy 10 bags 50-pound sandbags. This should be enough to get the job done.
Sand is more expensive than water. But given there are so many benefits of using sand, it really is worth it.
See Also: Portable Vs In-Ground Basketball Hoop Comparison
How To Fill Sand In Your Basketball Hoop?
Filling your basketball hoop with sand is pretty easy, actually. There are just a couple of steps you need to take.
Step 1 : Make sure to read the owners’ manual. There will be instructions and also things you need to know about your particular hoop.
Step 2 : Lay the hoop on the ground with the base plug facing upwards. It should balance on the rims.
Step 3 : Have someone hold the pole so it doesn't tip over when filling and then open the base cap.
Step 4 : Use a funnel to pour in the sand nicely so you don’t create a mess. Once filled, just the cap back on.
Step 5 : Lastly, turn the hoop back to the upright position, and voila! You are done. Having a couple of extra hands will be useful since a hoop filled with sand can get heavy. See? That wasn’t so hard, was it?
Wrapping Up
Alright then, now that you know how much sand for basketball hoop base you need, you can start pouring sand into your brand-new portable basketball hoop right away and start enjoying some fun games.
Remember to have someone that can help you with the process. 500 LBS of sand should do the trick. If there are any special instructions for your hoops, they should be mentioned in the instruction manual.
Related Posts You May Read:
1. How To Move A Basketball Hoop Filled with Sand
2. How To Keep Portable Basketball Hoop From Falling Over
3. How To Repair A Broken Portable Basketball Hoop Base
4. How To Get Sand Out Of Basketball Hoop Base
Tips for Filling a Portable Basketball Hoop
Skip to content
Your basketball hoop needs a solid foundation. Find out what you need to fill your hoop’s base.
Looking to bring the excitement of the basketball court to your home? Portable basketball hoops can be a great option for playing a pickup game with friends or a round of HORSE with your family.
But once you find the right portable hoop and get it home, don’t forget the most important step: filling the base. It’s crucial to properly fill the base to help increase the hoop’s stability during play, as well as in windy weather.
There are two common ways to fill a basketball hoop: with water and with sand. The owner’s manual you receive with your hoop will let you know how much to use of either. You can also use a base gel that mixes with water to become solid.
WATER
Adding water to the base is as simple as hooking a hose to the base hole. This is a cheaper and easier option than sand. If you plan on moving the hoop around a lot, water is a good choice since you can easily empty it from the base.
There are a few things you can do to help with stability and keep the base strong over time when using water:
Adding a small amount of bleach to the water can help avoid the growth of algae in the base.
If you live in an area with cold winters, the water in the base could freeze and expand. This can cause the base to crack. To avoid this, add a small amount of nontoxic antifreeze. You can also empty the base and store it indoors during colder months.
Water can evaporate and leave the hoop less stable, so checking the water level regularly is key.
Examine the base for any leaks over time. This can help to keep it upright for your next pickup game.
SAND
Sand is denser than water, and it weighs more per gallon, so it can help increase stability. But while it may make for a more stable hoop, sand can also make hoops difficult to move.
Another drawback to sand is that it can be hard to add — especially if wet — and even harder to get out of the base of your hoop.
Many hoop owners choose “play sand,” like the kind used to fill kids’ sandboxes, to fill the base since it can be smoother and more even. Using a funnel while filling the base can help decrease the chances of spilling sand.
BASE GEL
A third option for your hoop is a special gel designed to stabilize bases. Made of absorbent polymer, you will mix the gel with water. This mixture can become the equivalent weight of several bags of sand. Designed to be both mold-resistant and freeze-thaw durable, base gel can last several years. Once firm, it can also resist small holes or cracks that can cause leaks.
No matter what you use to fill your base, it’s always a good idea to have two adults move the portable hoop if needed. Also, it’s advised not to use weights, bags of cement or bricks to hold the hoop down.
Now that you know what to do to keep your portable hoop firmly on the ground, it’s time for tip-off. With a solid base for your hoop, you’ll be able to focus on hitting a long-range three or guarding against uncle Joe’s legendary jump shot during your next family pickup game.
Related Articles
How to equip a basketball court in the country or in the yard
Basketball develops the child's physical abilities - coordination, endurance, develops strong-willed qualities, concentration, attentiveness and teaches non-standard thinking. Professionals recommend sending a child to the basketball section from the age of 8-9, but outside the city or in the yard, you can “chase the ball” from an early age.
I myself equipped a basketball court in my country house and now I am ready to share the secrets of its arrangement. I'll tell you what you need to do, how to choose the right equipment and how to care for it.
Prepare basketball court surface
To create a basketball court in accordance with all the rules, you need to select a flat horizontal surface for it and fill it with concrete. After that, I recommend applying a special rubber coating, like on playgrounds in the yard. There is a more expensive coating option - from rubber.
The coating will provide cushioning - the ball will bounce well.
If it is not possible to organize a special platform, you can simply place a rack or hanging basket on a dirt surface. In this case, the ball bounce will not be so strong. An important requirement for safety: the surface must be flat, without holes and bumps.
The dimensions of the site depend on the features of your yard or plot in the country. A full-fledged basketball court has dimensions of 28 × 15 meters. However, not everyone has the opportunity to build such a site in the country.
It is necessary to take into account the technical features of the game. The three-point line in basketball is 6.75 meters from the hoop. Therefore, it is necessary that the size of the site be at least 10 × 13 meters. If you are not going to train three-point shots, a 5 × 5 meter court will do.
Mark out
The second step is to mark up. It is important to use paints of contrasting colors. It is better to buy paints with a high content of rubber or polymer.
If you are equipping a basketball court for children, make the markings bright so that they cheer you up and attract attention. For the game of teenagers and adults, it is better to immediately apply technically correct markings.
Place a small fence or protective net on the site. Thanks to them, you do not have to constantly run after the ball to the other end of the site.
Buy stand or backboard
It is difficult to answer the question of what is better - a basketball stand or a backboard. It all depends on taste, tasks and opportunities. Each of these types of equipment has its pros and cons.
There are two types of racks: mobile and static. The static one is mounted in the ground.
The base of the mobile rack is filled with sand or water - for stability. The main advantage of a mobile rack is that it can be moved from place to place. This is convenient when there is no dedicated basketball court or if you are going to play other games in this area, such as tennis or football.
The main requirement for racks is their stability. It will be much more comfortable and safer to play if you are sure that the stance will withstand a blow of any force.
Pay attention to the materials from which the racks are made. A static rack will be outdoors throughout the year, which means it must be made of reliable materials. It is better to buy racks from well-known manufacturers. So, the American companies Spalding or Royal Fitness guarantee high quality, durability and safety.
Basketball backboards can be made in the country with your own hands from a board, chipboard or plywood remnants. If this option does not suit you, you can purchase semi-professional or professional options in stores.
There are four types of materials from which the shield surface is made: composite, polycarbonate, acrylic and tempered glass. The first one is the cheapest. It is intended for entry-level players. Now manufacturers offer a large selection of colors. A carbonate backboard will provide a good bounce of the ball. An acrylic shield is bought to hold competitions or intense games.
The mobile stand can be moved, so it is suitable for a playground in the country and for those who want to play other games besides basketball
Shields and racks made of tempered glass look solid. They will be appreciated by experienced basketball players
Pay attention to rings
You can buy cheap rings, but I don't recommend doing that. In a year they will deteriorate and you will have to buy new ones. Basketball hoops from Spalding and Royal Fitness are made from quality metal that won't rust in the rain.
The ring must have a springy structure - no rigid attachment to the shield.
According to NBA rules, the ring must be fixed at a distance of about three meters from the ground. For a game with the participation of younger students, it can be hung lower so that it is not very easy to hit it, but at the same time it is quite possible.
Choose rings made from high quality metal to last for many years. For a game involving adults and teenagers, metal chain rings are suitable. They are distinguished by durability and strength.
Know what types of basketballs exist
Success in the game depends on the basketball.
They are divided by size. Size 7 is for men, 5 for women. Even smaller balls are bought for children. The size 6 ball is suitable for street ball or street basketball where the game is played on half the field.
You also need to take into account where you will play the ball: on the street or in the hall. The street ball has a stronger bounce, it is harder and more wear-resistant, but the indoor ball is more convenient to hold in your hands.
It is important to pay attention to the composition of the basketball. Well-known companies use complex polymer compositions for its production. The more expensive the ball, the more complex the polymer composition. The quality of the material determines how comfortable it will be for the players to hold the ball, what kind of rebound it has from the floor and from the bow of the ring.
Another important nuance: do not forget to purchase a pump with any needle.
If you want the ball to have good grip and bounce well, you need to choose polymer models from world famous manufacturers
Proper care
Professional athletes are ready to play in any weather, but amateurs are better off not following their example. If you don't properly store, use and care for your basketball arsenal, its lifespan will be shortened. Humidity will ruin the ball and all equipment, so you can’t leave them outside during rain and snow.
Balls should be stored only in a dry and ventilated room at a temperature of 10 to 20 °C.
Before winter storage, water must be poured out of the base of the mobile rack, and then removed from the street. If you don't feel like doing this every time, fill the rack with sand. Then it will not need to be constantly moved. Basketball stands from Royal Fitness can be left outside in the winter.
Points to remember when setting up a basketball court
The area needs to be determined. The classic version - 28 × 15 meters - is not suitable for everyone. For a dacha, a 5 × 5 meter area will be enough if you want to train three-point shots.
Don't forget the markup. It should be in a contrasting color. Bright colors will interest children and cheer them up.
It is necessary to install a protective net so as not to constantly run after the ball to the other end of the area.
If the shield is stable, then it is safe. A mobile stand from a well-known manufacturer will also not let you down, and it can be moved around the site.
When choosing a basketball, you need to focus on the players. For games involving children and adults, balls of different sizes are needed.
If you want a basketball ring that doesn't rot in a year and you don't have to spend money on buying a new one, choose rings from well-known manufacturers made of high quality metal.
Don't forget about care. Do not leave equipment and inventory on the street. Racks need to be removed to the house for the winter.
DIY Basketball Hoop Sizes
0126
Make your own basketball hoop? Easily!
Did you have to restrain yourself when you were walking past the basketball court to avoid throwing the ball into the basket? Why hold back? Team sports reliably unite people of any age, religion and social status. And to look decent at any moment and on any site, you just need not start training.
Small places for playing streetball can be equipped on sports grounds near the house, and rings can be built in summer cottages for children to play from improvised means. So, how to make a basketball hoop yourself?
Dimensions and materials required
Basketball hoop inner diameter 45 cm;
the height of its upper edge above the playing area is 3.05 m;
ring material - metal bar, plastic pipe, improvised materials;
rod or tube diameter for ring - 16-20 mm;
distance from ring to shield - 15 cm;
mesh length - 40-45 cm;
mesh material - metal chain, synthetic cord, rope, braid.
Types of basketball hoops:
metal with anti-vandal nets made of metal chain;
metal with rope mesh;
plastic with nets of various types of materials;
creative (from the remains of construction, from old furniture, from large plastic containers).
The construction of a ring from a metal bar begins with marking. Since the basket must have an internal diameter of 45 cm, a rod or pipe is selected based on this.
The material length is calculated using the formula:
Bar length = Circle diameter x 3.14 (pi value). We have 45 × 3.14 = 141.3 cm.
Since we need to fasten the ring to the shield, we take the length of the bar about 150 cm. You can bend the bar or pipe on the template (wheel), or you can bend it to size, measure the diameter and straighten with a mallet. The rest of the bar or pipe should be prepared for fastening to the shield using drilled holes and screws.
The ring is ready. Now you can make a grid to it. If it is assumed that the ring will hang in the adjacent territory of an apartment block, then it is better to make the grid anti-vandal, using a metal chain. The mesh is attached to the ring with 12 lugs or a smaller diameter rod welded on the bottom of the main ring.
Rope, braid, twine net can be woven by yourself. To do this, the material 20 m long, from which the mesh is prepared, is cut into segments of 160 cm each. If the mesh is supposed to be hung on 12 loops, then 12 segments are prepared.
When hanging pieces of rope on the ring, each section is picked up by a marine knot. The next row of weaving begins with knots connected by a series of hanging ends. So you need to weave 4-5 rows. For the beauty and neatness of the product, you can use a template by placing it under the knots to be connected. The lower ends of the rope should be melted to prevent fraying.
How to make a basketball backboard with your own hands, read this article.
1000sovetov.ru
It's not difficult to please your family and friends: how to make a basketball hoop with your own hands at home
Basketball is a great game, and the yard option is the most democratic sport. It can be played with a team of 6-8 people or practice throws alone.
A basketball hoop installed in the backyard or in the yard is sure to gather fans of this sport around. Moreover, often a home-made product is better than purchased options, since the age, height, and preferences of the players are taken into account.
It can be an order of magnitude stronger and more durable than store-bought. And a person receives much more moral satisfaction from a hand-made ring.
Facebook
Twitter
Google+
Vkontakte
Odnoklassniki
First, you need to decide which ring you want to get in the end. Just a basket with a wall or tree mount, or a complete shield complete with everything you need. Then - choose a place to install the shield and prepare the site. The next step is to break it down into steps.
Photo 1. Scheme of a standard basketball backboard with necessary measurements. To play in the yard, it is not necessary to consider all of them.
Tools and materials
jigsaw for metal;
wood saw;
drill or hammer drill;
adjustable wrenches;
paint and brush.
To make the ring, you can use thick steel wire, at least 5 mm in diameter, an iron strip or an old hula hoop. It will have to be shortened a little in the future. For the manufacture of the shield, plywood will be used, at least 5 mm thick. If the shield is installed in the yard, then a strong pillar is provided for support.
Dimensions
The size of the ring should be 45 cm in diameter (slightly larger than a basketball). The size of the shield is 180x105 cm.
The product will be attached at the bottom of the shield: 5 cm from the edge. So, from the ring to the top of the shield should be exactly 1 meter.
The shield can be hung at any height depending on the average height and age of the players. But it is also possible on the standard one - 3 m 5 cm.
This will allow the players to feel comfortable on any standard court in the future.
View
If the ring is attached not just to a tree, wall or post, but has its own shield, then it must have an appropriate view. The shield is usually white with black stripes around the perimeter and a painted square directly above the net. The size of the square is 45 cm high and 56 cm wide. This standard will make the game correct and help to put the ball directly into the basket, because if it hits the square, it will bounce right on the target.
Making a basketball hoop
If the ring is made of wire or steel strip, then it must be wound around a cylindrical object and fastened both ends. If from the hula-hoop tube, cut out the unnecessary part of the hoop with a hacksaw and reconnect the ends. When making a ring, you need to remember to make fasteners, for example, bend the ends of the wire in one direction, so that you can then attach them to the shield.
There must be a net on the ring: after the ball hits the target, it will direct it straight down, and not to any corner of the court. To make it, you need a long cord.
Pieces of cord, approximately 20 cm each, must be tied to the ring at such a distance that they evenly cover the entire circumference at 12 points.
Then with another segment in a circle, tie all the ropes, and so several times with an interval of 5-6 cm. The net is ready.
The shield is sawn with a jigsaw or a hacksaw, after marking with a pencil. After that, the product can be painted.
Important! The black stripes and the square above the basket on the shield must be 5 cm wide, otherwise they will simply not be visible.
After the paint has dried, you can attach a ring to the shield, and fix the shield itself to a pole or wall. The rate and type of fasteners depends on what the ring was made of and how the shield will be attached. The main thing is to calculate so that the structure can withstand at least 40-50 kg of load.
Mounting at home
If the ring is made of round wire, and its ends are bent down, then they can be pulled to the shield with 2 bolts connected by a metal plate in the area of the caps.
If the ring is made from a wide iron strip, then the ends must first be bent so that the strip fits snugly against the shield.
Such a product is also fastened with bolts threaded through pre-drilled holes in the strip and plywood.
If the shield is not available and the ring is to be attached directly to the wall, anchors can be used instead of bolts. In this case, you will need a puncher to make holes in the wall.
To a tree or wooden post, the ring can be nailed with 100 mm nails or screwed with long screws.
Attention! Whatever type of fastening is used, one thing unites them - it is necessary to put the ring on a horizontal level. If it hangs crooked, then the ball will slide off the edges past the basket.
After the shield and ring are fixed, the site is prepared. It should not have stones, puddles, and protruding stumps. Basketball is a very traumatic sport and players do not need any extra risk at all, they will stumble over a bush, stump or stone sticking out on the court. If the ring is installed indoors, then before the game you need to make sure that everything that breaks easily is hidden, and the glass on the windows is securely protected.
Watch a video showing how to make a basketball hoop from a metal rod.
Which ring is better, homemade or purchased. There is no definite answer here. A homemade product performs sports functions and is aesthetically pleasing to family members and friends of the manufacturer.
Even if outwardly it is a little more unsightly than store bought. In addition, home-made is calculated for certain loads. Whereas a store product, it is not known how much it will sag in conditions of harsh operation.
On the other hand, a high-quality, expensive, handmade ring with a shield, produced at the factory in compliance with all sizes and state standards, is unique. So it's up to the players to choose.
Rate the article:
Be the first!
Average rating: 0 out of 5. Rated by: 0 readers.
Share with your friends!
Facebook
Twitter
Google+
Vkontakte
Odnoklassniki
sportyfi. ru
DIY basketball hoop
Basketball is a great game, and the yard version is the most democratic kind of sport. It can be played with a team of 6-8 people or practice throws alone.
A basketball hoop installed in the backyard or in the yard is sure to gather fans of this sport around. Moreover, often a home-made product is better than purchased options, since the age, height, and preferences of the players are taken into account.
It can be an order of magnitude stronger and more durable than store-bought. And a person receives much more moral satisfaction from a hand-made ring.
ontakte
Odnoklassniki
First, you need to decide which ring you want to get in the end. Just a basket with a wall or tree mount, or a complete shield complete with everything you need. Then - choose a place to install the shield and prepare the site. The next step is to break it down into steps.
Photo 1. Schematic of a standard basketball backboard with required measurements. To play in the yard, it is not necessary to consider all of them.
Tools and materials
jigsaw for metal;
wood saw;
drill or hammer drill;
adjustable wrenches;
paint and brush.
To make the ring, you can use thick steel wire, at least 5 mm in diameter, an iron strip or an old hula hoop. It will have to be shortened a little in the future.
For the manufacture of the shield, plywood will be used, at least 5 mm thick. If the shield is installed in the yard, then a strong pillar is provided for support.
The ring should be 45 cm in diameter (slightly larger than a basketball). The size of the shield is 180x105 cm.
The product will be attached at the bottom of the shield: 5 cm from the edge. So, from the ring to the top of the shield should be exactly 1 meter.
The shield can be hung at any height depending on the average height and age of the players. But it is also possible on the standard one - 3 m 5 cm.
This will allow the players to feel comfortable on any standard court in the future.
View
If the ring is attached not just to a tree, wall or pole, but has its own shield, then it must have an appropriate view.
The shield is usually white with black stripes around the perimeter and a painted square directly above the net. The size of the square is 45 cm high and 56 cm wide.
This standard will make the game correct and help to put the ball directly into the basket, because if it hits the square, it will bounce right on the target.
If the ring is made of wire or steel strip, then it must be wound around a cylindrical object and fastened both ends. If from the hula-hoop tube, cut out the unnecessary part of the hoop with a hacksaw and reconnect the ends. When making a ring, you need to remember to make fasteners, for example, bend the ends of the wire in one direction, so that you can then attach them to the shield.
There must be a net on the ring: after the ball hits the target, it will direct it straight down, and not to any corner of the court. To make it, you need a long cord.
Pieces of cord, approximately 20 cm each, must be tied to the ring at such a distance that they evenly cover the entire circumference at 12 points.
Then with another segment in a circle, tie all the ropes, and so several times with an interval of 5-6 cm. The net is ready.
The shield is sawn with a jigsaw or a hacksaw, after marking with a pencil. After that, the product can be painted.
Important! The black stripes and the square above the basket on the shield must be 5 cm wide, otherwise they will simply not be visible.
After the paint has dried, you can attach the ring to the shield, and fix the shield itself to a pole or wall. The rate and type of fasteners depends on what the ring was made of and how the shield will be attached. The main thing is to calculate so that the structure can withstand at least 40-50 kg of load.
Mounting at home
If the ring is made of round wire, and its ends are bent down, then they can be pulled to the shield with 2 bolts connected by a metal plate in the area of the caps.
If the ring is made from a wide iron strip, then the ends must first be bent so that the strip fits snugly against the shield.
Such a product is also fastened with bolts threaded through pre-drilled holes in the strip and plywood.
If the shield is not available and the ring is to be attached directly to the wall, anchors can be used instead of bolts. In this case, you will need a puncher to make holes in the wall.
To a tree or wooden post, the ring can be nailed with 100 mm nails or screwed with long screws.
Attention! Whatever type of fastening is used, one thing unites them - it is necessary to put the ring on a horizontal level. If it hangs crooked, then the ball will slide off the edges past the basket.
After the shield and ring are fixed, the site is prepared. It should not have stones, puddles, and protruding stumps.
Basketball is a very traumatic sport and players do not need any extra risk at all, they will stumble over a bush, a stump or a stone sticking out on the court.
If the ring is installed indoors, then before the game you need to make sure that everything that breaks easily is hidden, and the glass on the windows is securely protected.
Watch a video showing how to make a basketball hoop from a metal rod.
Which ring is better, homemade or purchased. There is no definite answer here. A homemade product performs sports functions and is aesthetically pleasing to family members and friends of the manufacturer.
Even if outwardly it is a little more unsightly than store bought. In addition, home-made is calculated for certain loads. Whereas a store product, it is not known how much it will sag in conditions of harsh operation.
On the other hand, a high-quality, expensive, handmade ring with a shield, produced at the factory in compliance with all sizes and state standards, is unique. So it's up to the players to choose.
The summer season will come very soon, and many parents with their restless children will leave the city. Adults, as usual, will dig in the beds, but what should bored children do at this time? In this article, we have prepared information for you on how to make a basketball hoop with your own hands, and with it a playground.
Choosing the location of the site
This issue must be approached very responsibly, because many factors must be taken into account. It is desirable that the playground is located at a distance from the house and from the garden.
So, here are the places that would never be suitable for a basketball court:
On uneven terrain. Any sports ground implies a perfectly flat playing surface.
Near water bodies. It is contraindicated to play near any bodies of water, especially if you have children. It is possible that the ball will fall into the water and the fidgets, wanting to show their independence to their parents, will go to get it themselves. They will most likely end up in trouble.
In the lowlands. There, the site will dry for a very long time after various precipitations, which means that it will be used very rarely and will soon be abandoned.
Playing grounds near ground water are also prohibited. Every year the landscape will change, as a result of which the fixation of the shield with the ring will warp.
Creating the surface of the court
0005
Remove topsoil from the surface. To do this, dig in about 50 cm of earth. Such a procedure is necessary in order to continue laying the drainage cushion, which is laid in front of the main coating.
Lay the geotextile on the soil. To do this, it is cut into separate pieces, because it goes in a whole canvas. Such pieces can be stacked in any position. The main thing to consider is that they cover each other by about 20-30 cm, which excludes subsidence of the upper layer.
After that, the geotextile is sprinkled with sand and leveled, the thickness of such a layer should be approximately 15 cm. The grate is half filled with sand, and the other half with crushed stone. The layer thickness also remains 15 cm.
Fill with cement to form expansion joints. This is necessary so that the top coating is well fixed for a long time. In addition, after various precipitations, water will quickly seep through all layers, which will contribute to the rapid drying of the playing place.
After all steps have been taken, the topmost layer is placed on the treated surface. It can be any surface: a sports lawn, a special mixture of sand and clay, a roll coating, and others.
Setting up a basketball corner
Even when the foundation was just being installed, we should have thought about where our hoop would hang. For convenience, racks with rings are installed along the edges of the site, as in a real gym. Here are the dimensions to be met:
The minimum distance between posts is 3 meters.
The area of the field must be approximately 20 x 35 m.
The ring itself must be approximately 2 m above the ground.
Making a backboard
Making a basketball hoop with your own hands, like a backboard for it, is not difficult at all. To make a shield on our own, we just need to adhere to the following algorithm:
Make a frame from metal corners that need to be welded together according to the given dimensions.
Select the necessary boards to make the wall. When they are fastened together, some gaps may remain, but they will not interfere with the game at all. Just make sure the boards are level.
Next, the finished shield must be painted to your liking. Children can be involved in this procedure, because, as you know, they are the best designers.
We make the main component
Here we will look at the classic braided version and learn how to make a basketball hoop with your own hands. In general, it is not so difficult to make, the main thing is to show a little accuracy and desire.
To create braided rings, summer residents will need only two things:
The base of the ring. Usually it must be made of iron.
Strong threads. They can be seen: thin rope, cords, thick yarn, any rope.
So, what needs to be done in order for its main component to appear on your site:
At the very beginning, you need to make an iron blank in the shape of a ring and highlight a small ledge in it. The diameter of the circle must be such that the ball can pass freely into it. It is better to entrust such work to the stronger sex.
Then comes women's work. To do this, we take a rope and cut it into 8 equal parts. Then you need to tie them at the previously planned distance so that two ends of one thread hang down.
Now it's time to start weaving the mesh. To do this, the adjacent ends of the segments of a thick thread are tied into knots, obtaining different grid cells. All ends of the ropes are required here. Thus, it is necessary to make several layers of cells until the threads run out.
Which ring is better?
After making a basketball hoop with your own hands, you involuntarily wonder what is better: a shop hoop or something we made ourselves?
Of course, a handmade item is always the most pleasing to the eye. But it takes much more time to make it than a ring that can be bought in a store in a couple of minutes. But still, if there is no time to make this item on your own, it is better to purchase it in a special store with sporting goods.
So, in this article, you have learned how to properly install the court, as well as how to make a basketball hoop with your own hands for your beloved children who will use it for a long time to come. Most likely, you yourself will be interested in being active and participating in the game.
Source: https://serviceyard.net/sovetyi/basketbolnoe-koltso-svoimi-rukami. html
The summer season will come soon, and many parents with their restless children will leave the city. Adults, as usual, will dig in the beds, but what should bored children do at this time? In this article, we have prepared information for you on how to make a basketball hoop with your own hands, and with it a playground.
Choosing the location of the site
This issue must be approached very responsibly, because many factors must be taken into account. It is desirable that the playground is located at a distance from the house and from the garden.
So, here are the places that are by no means suitable for placing a basketball court:
On uneven terrain. Any sports ground implies a perfectly flat playing surface.
Near water bodies. It is contraindicated to play near any bodies of water, especially if you have children. It is possible that the ball will fall into the water and the fidgets, wanting to show their independence to their parents, will go to get it themselves. They will most likely end up in trouble.
In the lowlands. There, the site will dry for a very long time after various precipitations, which means that it will be used very rarely and will soon be abandoned.
Playing grounds near ground water are also prohibited. Every year the landscape will change, as a result of which the fixation of the shield with the ring will warp.
Creating the surface of the court
0005
Remove topsoil from the surface. To do this, dig in about 50 cm of earth. Such a procedure is necessary in order to continue laying the drainage cushion, which is laid in front of the main coating.
Lay the geotextile on the soil. To do this, it is cut into separate pieces, because it goes in a whole canvas. Such pieces can be stacked in any position. The main thing to consider is that they cover each other by about 20-30 cm, which excludes subsidence of the upper layer.
After that, the geotextile is sprinkled with sand and leveled, the thickness of such a layer should be approximately 15 cm. The grate is half filled with sand, and the other half with crushed stone. The layer thickness also remains 15 cm.
Fill with cement to form expansion joints. This is necessary so that the top coating is well fixed for a long time. In addition, after various precipitations, water will quickly seep through all layers, which will contribute to the rapid drying of the playing place.
After all steps have been taken, the topmost layer is placed on the treated surface. It can be any surface: a sports lawn, a special mixture of sand and clay, a roll coating, and others.
Setting up a basketball corner
Even when the foundation was just being installed, we should have thought about where our hoop would hang. For convenience, racks with rings are installed along the edges of the site, as in a real gym. Here are the dimensions to be met:
The minimum distance between posts is 3 meters.
The area of the field must be approximately 20 x 35 m.
The ring itself must be approximately 2 m above the ground.
Making a backboard
Making a basketball hoop with your own hands, like a backboard for it, is not difficult at all. To make a shield on our own, we just need to adhere to the following algorithm:
Make a frame from metal corners that need to be welded together according to the given dimensions.
Select the necessary boards to make the wall. When they are fastened together, some gaps may remain, but they will not interfere with the game at all. Just make sure the boards are level.
Next, the finished shield must be painted to your liking. Children can be involved in this procedure, because, as you know, they are the best designers.
We make the main component
Here we will look at the classic braided version and learn how to make a basketball hoop with your own hands. In general, it is not so difficult to make, the main thing is to show a little accuracy and desire.
To create braided rings, summer residents will need only two things:
The base of the ring. Usually it must be made of iron.
Strong threads. They can be seen: thin rope, cords, thick yarn, any rope.
So, what needs to be done in order for its main component to appear on your site:
At the very beginning, you need to make an iron blank in the shape of a ring and highlight a small ledge in it. The diameter of the circle must be such that the ball can pass freely into it. It is better to entrust such work to the stronger sex.
Then comes women's work. To do this, we take a rope and cut it into 8 equal parts. Then you need to tie them at the previously planned distance so that two ends of one thread hang down.
Now it's time to start weaving the mesh. To do this, the adjacent ends of the segments of a thick thread are tied into knots, obtaining different grid cells. All ends of the ropes are required here. Thus, it is necessary to make several layers of cells until the threads run out.
Which ring is better?
After making a basketball hoop with your own hands, you involuntarily wonder what is better: a store hoop or something we made ourselves?
Of course, a handmade item is always the most pleasing to the eye. But it takes much more time to make it than a ring that can be bought in a store in a couple of minutes. But still, if there is no time to make this item on your own, it is better to purchase it in a special store with sporting goods.
So, in this article, you have learned how to properly install the court, as well as how to make a basketball hoop with your own hands for your beloved children who will use it for a long time to come. Most likely, you yourself will be interested in being active and participating in the game.
The thing you need to know is most portable basketball hoops in the market will have a 35-gallon water capacity. This can be different for other models, but 35-gallons based hoop is pretty standard.
It should balance on the rims.
How To Move A Basketball Hoop Filled with Sand
The owner’s manual you receive with your hoop will let you know how much to use of either. You can also use a base gel that mixes with water to become solid.
Once firm, it can also resist small holes or cracks that can cause leaks.
A full-fledged basketball court has dimensions of 28 × 15 meters. However, not everyone has the opportunity to build such a site in the country. 
It is better to buy racks from well-known manufacturers. So, the American companies Spalding or Royal Fitness guarantee high quality, durability and safety. 
They will be appreciated by experienced basketball players 
If you don't properly store, use and care for your basketball arsenal, its lifespan will be shortened. Humidity will ruin the ball and all equipment, so you can’t leave them outside during rain and snow. 
And to look decent at any moment and on any site, you just need not start training. 
To do this, the material 20 m long, from which the mesh is prepared, is cut into segments of 160 cm each. If the mesh is supposed to be hung on 12 loops, then 12 segments are prepared. 
Moreover, often a home-made product is better than purchased options, since the age, height, and preferences of the players are taken into account. 
The shield is usually white with black stripes around the perimeter and a painted square directly above the net. The size of the square is 45 cm high and 56 cm wide. This standard will make the game correct and help to put the ball directly into the basket, because if it hits the square, it will bounce right on the target. 
ru 
To play in the yard, it is not necessary to consider all of them. 
To make it, you need a long cord. 
It is possible that the ball will fall into the water and the fidgets, wanting to show their independence to their parents, will go to get it themselves. They will most likely end up in trouble. 
In general, it is not so difficult to make, the main thing is to show a little accuracy and desire. 
All ends of the ropes are required here. Thus, it is necessary to make several layers of cells until the threads run out. 
html 
They will most likely end up in trouble. 
The grate is half filled with sand, and the other half with crushed stone. The layer thickness also remains 15 cm. 
