Home » Misc » How to change the height of a basketball hoop
How to change the height of a basketball hoop
How to Adjust Basketball Goal Height
Need help? Call Us!
M-F 8-5 CST
Product Search
Need help? Call Us!
M-F 8-5 CST
Product Search
Product Search
/ Articles / How to Adjust Basketball Goal Height
The process used to adjust the basketball goal height depends completely on the type of basketball system you own. Please note: if you own a "fixed height" basketball system, your basketball goal height may not be changeable. Some fixed height units are made with a solid pole that has no moving parts. Other fixed height basketball goals employ an extension arm that is clamped to the post using bolts to hold the arm in place. To change the rim height simply loosen the bolts, slide the arm up or down the post and tighten the bolts to hold in place.
Below is a summary of some of the more popular adjustment methods on the market.
Rear Crank - basketball goals of this type have a crank handle on the back side of the post. Turn the crank handle clockwise to raise the rim height, counterclockwise to lower.
Front Crank - basketball goals of this type have an adjustment cylinder located on the front side of the post. The adjustment cylinder has a loop at the bottom that receives a removable crank handle. Insert the hooked end of the crank handle into the adjustment loop. Then turn crank handle clockwise to raise rim height, counterclockwise to lower.
Quick Pin - these basketball goals have a spring balanced removable pin on the back side of the post. To change rim height simply slide pin to remove, then raise or lower rim height by pushing or pulling adjustment handle up or down. Replace pin at any desired height setting.
Squeeze trigger - this type using a pneumatic cylinder and a squeeze trigger on the back side of the post. Squeeze trigger, then pull down or push up on handle. When rim reaches appropriate height, release the squeeze trigger. The rim height will stay at the height where you released the trigger.
InstaJust - also known as a "stick adjust" this type of adjustable basketball goal uses an adjustment mechanism located directly behind the rim. Using a broom handle, insert one end then room handle into the cupped area of the instajust bracket and push up. Then allow the backboard and rim to descend to it lowest possible height. Then remove the broom handle and use it to push up on the bottom of the backboard. You will hear a "click" every six inches. Simply stop pushing upward when you reach the appropriate rim height. The rim will stay at the height when you stop pushing.
How To Lower A Basketball Hoop (8 Different Height Adjustment)
There is a need to lower the basketball hoop for various reasons. Generally, for tournaments and championships, the standard height is about 10 feet. But, for beginners and kids, sometimes it requires setting the height of the hoop at a little lower level. But how to lower a basketball hoop?
There are different types of hoops for basketball. The process to lower them is not the same for all. Moreover, it actually depends on the lifting mechanism.
In this article, you will learn about lowering those hoops regarding these mechanisms step by step.
Table of Contents
How Do You Lower A Basketball Hoop?
1. Crank Handle Mechanism (Infinite Adjust)
2. Stick Adjust Mechanism (Preset Adjust)
3. One-Hand Adjustment Mechanism (Preset Adjust)
4. Screw Jack Lifting Mechanism (Infinite Adjust)
5. Telescope Mechanism (Preset Adjust)
6. Powered Lifting Mechanism (Preset Adjust)
7. Exactaheight Lifting Mechanism (Preset Adjust)
8. Trigger Glide Mechanism (Preset Adjust)
Lowering A Basketball Hoop: Manufacturer Based
How To Lower A Bison Basketball Hoop
How To Lower A Goalsetter Basketball Hoop
How To Lower A Lifetime Basketball Hoop
How To Lower A Huffy Sports Basketball Hoop
How To Lower A Spalding Basketball Hoop
How To Lower Goalrilla Basketball Hoop
How To Lower Little Tikes Basketball Hoop
How To Lower Basketball Hoop In Gym
Ending Note
How Do You Lower A Basketball Hoop?
It's time to lower the basketball hoop. The process of reducing the basketball hoop depends totally on the system you have installed. Needless to say, there are fixed height model basketball systems in which you may be unable to lower the hoop.
The process of lowering a basketball hoop is sometimes common for all. In this portion, we will learn about those adjustable hoops and the process of lowering them.
Mostly there, we found two categories of height adjustment for the basketball system.
1. Infinite Adjust: Most of the designs come with this adjustment system.
2. Preset Adjust: In this category, manufacturers customize the whole mechanism. Some mechanisms are patented as well.
In the latter portion, we will discuss some of the best height-adjustment mechanism types that top basketball system manufacturers provide.
1. Crank Handle Mechanism (Infinite Adjust)
In this mechanism, there is a height gauge in the system attached to the crank. To lower the hoop in this mechanism, you just need to rotate the crank clockwise or anti-clockwise, as referred to in the manual.
2. Stick Adjust Mechanism (Preset Adjust)
It is an ancient type of height adjustment mechanism that is still alive. It is also known as - Broomstick Adjustment, InstaJust, and Pole Mechanism regarding the manufacturer. To lower the basketball hoop in this system, there is an adjustment portion just behind the ring. You just need to-
Insert the pole or stick into the adjustment area.
Place the end of the stick into the release latch or cup.
Push the stick up.
After that, lower the hoop all the way to the lowest position.
Now place the stick at the bottom of the backboard and push it up to set the height.
3. One-Hand Adjustment Mechanism (Preset Adjust)
This mechanism is just one step up from the Stick Adjust Mechanism. It comes with an integrated handle to adjust the height. So, you don't need an additional broom or pole to raise or lower the system. If you want to lower the hoop, you just need to push the handle upwards, and it's done.
4. Screw Jack Lifting Mechanism (Infinite Adjust)
In the Infinite Adjust category, this mechanism is old enough. This system comes with a pre-built tool in the pole. By rotating the screw handle, you can easily raise or lower the hoop. You may find it just like the crank mechanism. But there is a difference. The crank handle is removable, but the screw jack is attached to the system.
5. Telescope Mechanism (Preset Adjust)
This mechanism is the new version in the Preset Adjust category. And the main part is that different manufacturers modified this mechanism on their own. They have customized the system. Some attached a tilting mechanism to complete the process of adjusting the height. In most cases, to lower the hoop-
Simply find the joint of adjustment.
Remove the nut and bolt.
And telescope the system down.
6. Powered Lifting Mechanism (Preset Adjust)
This mechanism is a patented mechanism by Lifetime Basketball System's manufacturer for adjusting the height. It is also known as the "Infinitely Adjustment System." This system comes with gas spring features. Its additional leverage and strength allow it to adjust the height effortlessly. To lower the hoop, you have to raise the leverage by pushing it up.
7. Exactaheight Lifting Mechanism (Preset Adjust)
This mechanism is developed with a pin with a spring counter. The pin works as a stopper or locker for the height. Here to lower the hoop-
Slide or remove the pin.
Gently push the handle upward, and the rim will go down.
8. Trigger Glide Mechanism (Preset Adjust)
This mechanism is a comparatively new concept for basketball height adjustment. It requires you to do nothing but hold the handle and move it up or down using the trigger to get the position. To lower the hoop in this mechanism, you need to raise the handle, and it's done.
Lowering A Basketball Hoop: Manufacturer Based
So far, we have known all the available adjustable mechanisms for the basketball hoops. Here, you will see which brands' systems follow which mechanisms and their lowering processes.
How To Lower A Bison Basketball Hoop
Bison is one of those companies with both fixed height and adjustable basketball playground systems. In the line of the height-adjustable system category, it has followed 2 mechanisms.
The first one is the Crank Handle Mechanism, which requires rotating the handle clockwise to lower the hoop. And the second one is the Stick Adjust Mechanism, which requires a broomstick or a pole to raise or lower the hoop.
How To Lower A Goalsetter Basketball Hoop
Among different models, Goalsetter has its Adjustable In-Ground category. And the best part is that almost each and every model in this category are manufactured with a Screw Jack Lifting Mechanism.
So to lower the hoop, you just need to rotate the screw handle, and it's done.
How To Lower A Lifetime Basketball Hoop
The Lifetime basketball system has a huge variety in its adjustable height category. In this category, there are 4 types of mechanisms that are common. They are- Telescope Mechanism with a tilting system, Stick Adjust Mechanism, One-Hand Adjustment Mechanism, and Powered Lift Mechanism.
In our previous heading, we have discussed all these mechanisms. Check out that portion to know how to lower the hoop regarding these mechanisms.
Top 5 Lifetime Adjustable Basketball Hoop Recommendation:
Lifetime Pro Court Adjustable Portable Basketball System
Lifetime 44 Inch Adjustable Portable Basketball System
Lifetime 1221 Height Adjustable Portable Basketball System
Lifetime 71525 In-Ground Basketball Hoop Review
How To Lower A Huffy Sports Basketball Hoop
Most adjustable huffy sports basketball hoops are manufactured following the ExactaHeight Lifting Mechanism. You need to slide the pin and move the handle upward to lower these basketball systems' hoops.
Also Read: Huffy Sports Adjustable Portable Basketball Hoop Review
How To Lower A Spalding Basketball Hoop
Spalding basketball system manufacturing company is well known for its different height adjustable basket playground systems. This company has a wide variety in this adjustable system category.
Screw Jack Lifting Mechanism, ExactaHeight Lifting Mechanism, Telescope Mechanism, Stick Adjust Mechanism, Trigger Glide Mechanism (Pro Glide Advanced Basketball System) - all these systems are integrated with different models.
In our previous heading, we have discussed these mechanisms broadly. Check out that portion to know how to lower Spalding basketball hoop regarding the mechanism.
Top 3 Spalding Adjustable Basketball Hoop Review:
Spalding NBA 71562 Hybrid Portable Basketball System
Spalding 66291 Pro Slam Portable Basketball System
Spalding Hercules 54 Inch NBA Portable Basketball Hoop
How To Lower Goalrilla Basketball Hoop
For the Goalrilla basketball system, Screw Jack Lifting Mechanism and Crank Handle Mechanism are common in the adjustable system category. In both mechanisms, you have to rotate the handle as referred to in the manual to lower the basketball hoops.
Best Goalrilla Adjustable Basketball Hoop Review:
Goalrilla FT Series In-Ground Basketball Hoop
Goalrilla GS54 In-Ground Basketball System
How To Lower Little Tikes Basketball Hoop
Apart from other professional basketball systems, the Little Tikes system is designed for kids. This easy-score basketball set comes with a height holding switch.
Now, a little tikes basketball hoop how to lower?
Pop the switch by pulling it out.
Choose your desired height by moving the inner pole. To lower it, just let it go inside.
Lock the switch back to the holding point.
How To Lower Basketball Hoop In Gym
Actually, it depends on which types of mechanisms are present in a gym basketball system. 2 types of systems are mostly found in the gym.
They are- the Crank Handle Mechanism and the Screw Jack Lifting Mechanism. Now, basketball systems following these 2 mechanisms are so rough and tough. That's why such systems are installed in the gym.
As mentioned before, you just need to rotate the handle to lower the hoop for such mechanisms. Apart from these systems, if you find other mechanisms, then check our previous discussions. We have discussed almost every type of mechanism.
Ending Note
Now you know how to lower basketball hoop regarding the adjusting mechanism. We have discussed almost every type of system available out there. Beyond all these, if you have seen any other basketball system, let us know.
After all, if you find any complications with lowering your basket hoop, check its manual. There must be a guideline for you if it is adjustable.
Relevant Articles:
How To Adjust Lifetime Basketball Hoop
How To Disassemble A Basketball Hoop
How To Install A Basketball Backboard To A Pole
How To Keep Basketball Hoop From Falling Over
Do-it-yourself basketball backboard with height adjustment (20 photos).
Basketball backboard dimensions and markings
Today we will talk about how to make a high-quality basketball backboard and basketball net with your own hands at home from improvised materials. We will also consider the technology of manufacturing a basketball backboard and a net for playing basketball for children or adults.
In order to make a simple DIY basketball hoop for kids, we need thick wire and rope. Instead of thick wire, you can take an old unused hula hoop, cut it, shorten it and reconnect it. It is important to leave a "sprout" for attaching the ring to the shield.
If you want to make a basketball hoop with your own hands from thick wire, then in order to get the most even circle, we recommend using a cylindrical fixture designed to serve as a template. We wind the wire around it. And do not forget to leave a "sprout" for attaching the resulting ring to the basketball backboard.
The diameter of the metal blank for the ring should be slightly larger than the diameter of the basketball. Then you should take the prepared rope and cut it into 20-22 identical segments. At the same time, the length of each should be 2.5 - 3 times greater than the planned length of the mesh hanging.
These pieces are attached to the metal ring at regular intervals. You need to tie the ropes exactly in the middle so that 2 ends of equal length remain free. Then we connect in turn 2 ends of nearby ropes around the entire circumference of the ring. This is the first level of our grid. Then, similarly, we tie the ropes to the next level, etc. If you want to make a basketball hoop for your home, you can tie the bottom of the net so that the ball will stay inside when it hits. This will help reduce the chance of an accidental bounce of the sports equipment after hitting the basket.
DIY basketball backboard for adults. How to make a professional basketball backboard - here you have to try. How to make a basketball backboard at home. The process of making a basketball backboard is no more difficult than making sports predictions, especially if the necessary materials are available.
Here is a typical instruction for making a basketball backboard at home. For the base of the basketball backboard, you can choose a sheet of plywood, which is inexpensive and not hard to get either. A sturdy rectangular piece of plexiglass or thick plastic may also work well.
If the basketball backboard will be installed outdoors, then it is worth choosing the material for its base based on considerations not only of strength, but also of resistance to adverse weather conditions.
The next step is to choose a place where the basketball backboard will be attached. When choosing such a place, the main thing to remember is that the lower edge of the shield should be at a height of 290 centimeters from the ground, and the ring should be located at a height of 305 centimeters.
Now you need to mark and cut out the dimensions of the plywood blank. The ideal size of a standard basketball backboard are the following parameters: width - 1.8 meters, height - 1. 05 meters. This size will allow players to make more accurate and varied throws.
Before you start cutting out the workpiece, you need to use a pencil to outline the dimensions and draw lines along which the workpiece will be cut. It is better to cut it with a jigsaw, when working with which you must be careful.
After the blank of the future basketball backboard is ready, it will be necessary to draw a white square on it, which plays a very important role.
The white square is a kind of guide for the players when shooting, with the help of such markings it is much easier to get the ball into the basket. If the ball is correctly thrown into the corner of this square, then it will definitely reach the goal.
In order to mark out such a square, not only a brush and paint are needed, but also knowledge of the dimensions of the rectangle. Its external dimensions are 59 centimeters horizontally and 45 centimeters vertically.
When marking out, it should also be taken into account that the upper edge of the base of this rectangle must coincide with the level of the upper plane of the ring. The width of the stripes of the square should be 5 centimeters.
Basketball hoops
Material - solid steel, inner diameter 45 cm and painted orange. The metal bar of the ring must have a minimum diameter of 16 mm and a maximum diameter of 20 mm. On the bottom of the ring there must be devices for attaching nets, such as to prevent injury to the fingers. The mesh must be attached to the ring at twelve equally spaced points along the entire perimeter of the ring. Net attachment devices must not have sharp edges or crevices that could get caught by the player's fingers.
The ring is attached to the structure supporting the basket so that no force applied to the ring is transmitted directly to the backboard. Therefore, there should be no direct contact between the ring and the device that secures the ring to the shield and the shield. However, the gap must be small enough that fingers cannot get into it. The top edge of each ring must be located horizontally at a height of 3. 05 m above the surface of the site at an equal distance from the vertical edges of the shield. The nearest point on the inside of the ring must be 15 cm from the face of the shield. You can use rings with a shock absorber.
Made of white cord and designed to hold the ball momentarily as it passes through the basket. The net length must be at least 40 cm and not more than 45 cm.
Each net must have 12 loops to attach to the ring. The top sections of the net must be sufficiently rigid to prevent: Net entanglement on the ring and possible entanglement. Ball stuck in the net or thrown out of the net by the net. Basketball net can be woven from braid, twine, rope, thick threads. The braid or thread is first cut into segments.
The length of each segment must be four times the length of the grid. The number of segments is determined as follows: the ring intended for the grid is measured, and the resulting value is divided by four. The do-it-yourself basketball backboard is almost ready. Now it needs to be firmly fixed. To do this, you will need 4 large bolts that can withstand a load of 30 kg, and drill four holes in the wall or any other place where the basketball backboard will be mounted.
Use a spirit level to drill holes evenly. After that, you can start installing the shield. It is very inconvenient to do it yourself, so you should again resort to the help of friends who can insure you on the stairs, as well as file and hold the shield.
Once the bolts are installed and screwed into place, the basket can be hung up so that you can finally play on the court with a new basketball backboard that will last for many years.
In short, you can make a good basketball backboard with your own hands. But it is important to pay attention to one serious point.
The fact is that no matter how it seems to us from the side that the contact of the ball and the basket hoop is quite soft, it should be noted that the impact load on the fastening of the hoop to the backboard is very high. The weight of the ball (if you do not go into the definition of physical values) during contact with the ring increases many times, even when thrown from an average distance.
Well, with an inaccurate hit from a long distance, this blow can reach destructive power. And such a load acts on the mount hundreds and thousands of times. So that your work does not go to waste, that is, the future ring with a shield is a reliable design, you need to pay maximum attention to attaching the ring to the shield and then the same shield to the wall or other structure. Regarding the material of the shield, it can be put together from the same inexpensive pine boards available, and preferably from harder wood. Proposals to make a basketball backboard from plywood, fiberboard, plastic do not stand up to criticism. The first two positions do not pass due to the fact that if your shield hangs in the season in the rain and the sun, nothing will remain of it.
Plastic will naturally withstand all of these weather conditions, but is unlikely to be affordable. Plastic plastic is different, because the one that is used in the gym is very expensive, another different lottery ... will stand it - will not stand it. But a wooden board, it is a material that has stood the test of time and history. It is known that the official dimensions of the basketball backboard are as follows - a width of 1 meter 80 centimeters and a height of 1 meter 5 centimeters.
But in principle, you can try to build a flat square of boards 3 cm thick and 80 cm x 80 cm in size, I think this area will be quite enough to play normally or work out the throw. Basically, only a square is actively used when throwing (its dimensions are 59centimeters, height 45 centimeters) above the hoop, since this is the small square you need to be able to hit if you want to perform a throw from the shield.
Then (if it hits this square), the ball will most likely fall into the ring. Even in this case, if you perform a throw with a rebound from the shield, the load on the shield itself will be very small, but on the fastening of the shield and the ring, in this case, the pressure will be maximum.
Basketball hoop is made from a metal rod with a diameter of 16 - 20 millimeters. I think everyone understands that in order to protect against atmospheric precipitation, the entire structure should be painted with the appropriate paint, which can be bought at the store, explaining to the seller why the paint is needed.
As a result, I will repeat myself and say that when trying to make a basketball backboard on your own, pay attention to the fastening of the ring to the backboard. This is the most fragile place in this design.
In this article you will learn:
What are the dimensions of the backboard with hoop
How to make a basketball hoop with your own hands
Where to buy a ready-made basketball backboard with a ring
Basketball-like games were found among the ancient Scandinavian peoples and Mexican Indians. Today in northern Mexico, one of these games is popular - "Pok-Ta-Pok". It is believed that it appeared due to religious rites, which eventually turned into sports fun and an attraction for tourists. How the game "basketball" appeared, and what is a basketball backboard with a ring as a necessary element of this popular game, we will learn in this article.
When basketball and the first backboard with a hoop appeared
The forerunner of basketball is the 19th-century children's game "duck on the rock", familiar to the Canadian inventor of basketball James Naismith. The principle of the game was to hit a small stone on top of a large one.
The concept of basketball was finally formed when D. Naismith moved to the USA and became a physical education teacher at the Youth Christian Organization College (YMCA) in Springfield, Massachusetts. Already teaching physical education and as a college professor, he faced the challenge of creating a winter game between baseball and football. Naismith, given the weather conditions this time of year in Massachusetts, decided that this game should be played indoors.
Naismith's goal was to create an outdoor game for the students of the Christian Workers' School that required more than just strength and dexterity. It was supposed to develop coordination of movements in teenagers and at the same time be interesting.
So, in the winter of 1891, under the leadership of Naismith, the first basketball baskets were installed in the college gym. Baskets from under the fruit, fixed on both sides of the hall on the balconies, which encircled the room around the perimeter, acted as basketball hoops. Such baskets were fastened at a height of 3.05 m, it was this indicator that became the international standard, which is observed to this day.
The task of the players was to throw the ball (at that time they used football) into the basket. The first basketball match was held in the same hall on December 21, 1891. According to the conditions of the game proposed by Naismith, each team had 9 people, which exactly coincided with the number of students in the group.
The news of the new game quickly spread throughout America, and Naismith was asked to send the rules. On February 12, 1892, after learning the rules and mastering the basics of technology, the students of Springfield College played the first "official" match in the history of basketball, which ended in a 2-2 draw.
This meeting turned out to be so successful, and the rumor about a new type of competition spread so quickly that soon two Springfield teams began to hold demonstration competitions, which were already attended by hundreds of spectators. The initiative was picked up by students from other educational institutions, and the following year, the Northeast of America was swept by a real basketball fever.
The rules of basketball that Naismith wrote himself as a college instructor at 1891 year, was a list of 13 points, which eventually formed the basis of modern international rules, which hardly fit on 200 pages. In 1893, instead of baskets, they put iron rings with a grid, two years later they added shields, and two years later the team was reduced to 5 people.
What is a basketball backboard with a ring today? The shield is made of a transparent material, usually a single piece of tempered impact-resistant glass with a degree of hardness corresponding to that of a 30 mm thick hardwood shield.
It is allowed to produce such shields from other materials, but in this case they must be painted white and comply with other requirements for such sports equipment.
The front side of the shield is made smooth, a marking line is applied along the edges, a rectangle measuring 45 cm vertically and 59 cm horizontally is indicated at the place where the ring is attached. Moreover, the upper edge of the base of the rectangle must coincide with the level of the upper plane of the ring. White outlines are applied to transparent shields, and black is used in other cases. The width of the lines is 5 cm.
The basketball backboard with hoop is installed at right angles on both sides of the playing court, parallel to the front lines. The center of the front surface of each shield lies on perpendicular lines reconstructed from points located on the site at a distance of 120 cm from the middle of the inner edge of each front line.
Shields are upholstered, the following requirements apply to it:
the sides of the boards and the lower end are covered with soft material at a height of at least 35 cm from the bottom corners;
the lower end is upholstered with material at least 5 cm thick;
the rear and front surfaces of the shield should be decorated with upholstery material, the thickness of which is at least 2 cm, at a height of at least 2 cm from the bottom end.
The following requirements are imposed on the structures on which the shields are attached: their front parts, including upholstery, are placed at a distance of at least two meters from the outer edge of the front line. They are painted in bright colors that contrast with the walls of the sports hall in order to provide sufficient visibility to the players of both teams.
The structure on which the basketball backboard with the hoop is mounted is fixed to the floor of the court in such a way as to prevent it from moving during the game.
Structures used for fastening the shields must be upholstered with soft material behind the shield at a distance of 120 cm from the front surface of the shield. The minimum thickness of the upholstery is 5 cm, and the density is the same as that of the upholstery of the shields.
The base of the structure from the side of the playground is upholstered with dense soft material to a height of at least 215 cm, the thickness of the upholstery is 10 cm.
The minimum value of the so-called "indentation factor" of the upholstery of panels and structures is 50%. This figure means that when an appropriate force is applied to the upholstery, its indentation should be within 50% of its original thickness. The upholstery material provides protection to players from possible injuries during the game.
Basketball backboard and hoop dimensions
It's hard to imagine a basketball court without a basketball backboard and hoop. For them, world standards established by the International Basketball Federation have been adopted.
A basketball backboard is a rectangular or square panel to which a hoop is attached. Mounting is provided on the shield for mounting on a pole or hanging on a wall: rigid mounting is required, the product should not stagger and move.
Shield dimensions - 1.8x1.05 meters, with an installation height of 2.9 meters. By NBA standards, the size of the backboard must be 72x42 inches. Two shields are installed opposite each other from different ends of the field, the material is impact-resistant (as an option, tempered glass, acrylic, wood). Lines are drawn on a smooth surface. Models of basketball backboards with a net that are not intended for stationary installation are equipped with the same mounting elements as in the brackets for hanging punching bags. This method makes basketball backboards able to withstand a lot of weight and securely fixes them.
Ring or basket includes a metal (steel) circle covered with netting without a bottom. It is installed at a height of 3.05 meters from the floor and indented 15 cm from the lower edge of the shield. The inner diameter is selected from the range of 45–45.7 cm. The basketball hoop is painted in a bright color, usually orange. It is impossible to allow the transfer of load from the basket to the shield, therefore, the installation of the product is carried out with special attention.
DIY basketball hoop
Homemade basketball hoops are installed in summer cottages or hung in the yard near the house. In the summer, you can throw the ball with pleasure, feeling like Michael Jordan for a moment. This game is available to everyone: both children and adults. The benefits of such a seemingly simple exercise are incredible!
Have you set out to make your own basketball hoop and don't know where to start? Further, we will talk about this.
To make your own basketball hoop, you need thick wire and rope. Instead of a wire, an old unnecessary sports hoop is suitable, which is cut, shortened and connected again. Do not forget to leave a "sprout" for attaching to the shield.
Making a thick wire basketball hoop requires some trickery. To obtain an even circle, a cylindrical fixture can be used as a template on which the wire is wound. But, before cutting off the wire, do not forget about the "sprout" for attaching to the wall.
The diameter of the metal blank for the hoop is slightly larger than the diameter of a basketball. Next, the pre-prepared rope is cut into 20–22 identical segments. The length of each is 2.5–3 times the planned length of the net hanging.
These segments are attached to the metal ring at regular intervals. The ropes are tied in the middle, and the two ends of equal length are left free. Then the two ends of the nearby ropes are tied in turn, and so on along the entire circumference of the ring. It turns out the first level of the grid. The ropes of the next level are tied in the same way, and so on.
When making a basketball hoop for the home, the bottom of the net can be tied, which will allow the ball that hits the net to stay inside. Thus, the ball does not accidentally bounce to the side.
Now we know how to make our own basketball hoop. But it is necessary to answer the question, which is better - a home-made or a quality product bought in a store?
Making your own parts is fun. To do this, you only need free time, the necessary materials and a third-class welder. If you do not have this, then it is better to purchase a basketball hoop with a backboard from trusted manufacturers.
In order to make a basketball backboard with fastening, you will need six meters of a 2x2 cm profile pipe, 8.5 m of a 2x4 cm profile pipe, a backboard made of laminated moisture-resistant plywood, a basketball hoop, six anchor bolts for attaching to the wall. The design is assembled from three parts for easy wall mounting.
The desired part is cut off from the shield.
Metal structures are welded and the prepared AKZ is applied to them.
The shield is drawn, pasted over with adhesive tape, and lines 5 cm wide are applied to it.
Attach the shield to the frame.
Where to buy a basketball hoop with a backboard
In such an active game as basketball, every little thing is important! Even at the finish line, troubles happen: the ball is in the ring, but gets tangled in the net and gets stuck. This moment is ruined! How to avoid such troubles?
The following requirements apply to the ring net:
12 fastening loops;
length should be 40–45 cm;
use rigid white cord as material;
upper is made in such a way as to prevent throwing the net on the ring, tangling or sticking the ball.
How to choose the right basketball net? The main thing to pay attention to is the material, diameter and thickness of the thread, type.
Capron and nylon products are used more often. The latter is more wear-resistant, so for professional training, boron falls on this material.
The diameter is selected according to the diameter of the ring and the ball.
For professional basketball nets, thick threads of increased strength are used, but for amateurs, more fragile ones can be used.
Type: knotted and knotless. Products of the first type are widely used, but knotless basketball nets for the hoop look better and absorb the impact of the ball well, and are more reliable.
Looking for quality hoop backboards? We will help you make the right choice. Sportstyle started its activity in 1992 and has been successfully presenting its goods and services in the markets of Russia and neighboring countries for more than 20 years.
One of the main activities of the company is the production of sports equipment. Our products are very popular and in demand, among them:
boxes, rings, bags and pears;
wrestling mats;
equipment for sports aerobics and much more.
The range of our company is not limited to sports equipment. We are happy to produce for you tents for summer cafes and weddings, awning garages, trade tents, awnings for cars and boats, as well as pool bowls.
Our son became interested in basketball in the summer, and although there is a beautiful stadium with a basketball court half a kilometer from home, sometimes you want to knock the ball near the house. Therefore, it was decided to make a do-it-yourself basketball backboard near the fence (so that you could knock on a relatively hard road surface, and the ball would fly away, if it didn’t hit the ring, to our site, and not to someone else’s. We deviated a little from the standard and the dimensions we got are like this (photo is clickable)
The shield was cut out of OSB (just in case, we twisted two layers, and added one more, a small square, to strengthen the fastening - this can be seen in the photo below) and carefully painted with oil paint
The support was made of metal profiles 50*50 and 56*56 in size. The fact is that the part of the fence where the shield is attached is supposed to be removable for us - this is where we usually dump soil, crushed stone and other minerals. Therefore, it was decided to make the shield removable. Along with support. We implemented this idea like this.
A short post driven into a previously dug hole and cemented. The long one is fixed in it with screws. If necessary, it can be taken out. Actually, this is also visible in the diagram above.
Just before the shield was built, we had a welding machine, and this product proved to be a great workout. The pipes were welded with the letter G, a beautiful rectangle was welded to a short crossbar, on which a shield was attached.
Mesh rings are sold for little money in all sports shops and in many hyper stores. It turned out very nice.
Oh sport, you are the world!
There is nothing in the country, only bending metal, fumbling shish kebab, drinking beer. It is necessary to go in for sports both by ourselves and by children.
True, for this you will first have to "bend the metal" and celebrate this matter with beer and barbecue.
Another series of the project "Made of Metal" - a basketball backboard. Joint work of me and my father.
Batko studied the standards for the height and dimensions of a basketball backboard, made a wooden backboard, painted it, made wing screws, installed a pole. Well, in addition, he made critical remarks to the metal part.
I - designed the whole metal part and welded the metal.
Let's go!
01. First I sit down at the computer and sketch out the drawing of the shield and the pole itself.
The original plan was to put the ring in another place and pull it with a solid hitch to the nearest tree. But there turned out to be a lot of roots and they decided to put them in free flight and without a screed, which is why the ring in the upper part of the column remained rudimentary only in the drawing. Diagonals that are not in the drawing (green) have also been cancelled. We decided that the rigidity of the wooden shield and metal fasteners would be enough not to "walk".
Also on the move I changed the way of strengthening the outrigger knee. Not with a corner as in the drawing, but with two stripes on the sides, see the photo below.
A 5 cm profile was used for the pole, a 6 cm profile was used for the bracket strung on the pole. A strip is welded inside to prevent play. Everything that adjoins the wooden shield is a 25 mm corner.
Important: the ring must be universal for both adults and children of different heights. Therefore, a height offset system was made.
02. The main large elements are welded: a pole, a knee, two stepson solid fuel boosters. The upper edge of the pillar and stepchildren is bevelled: for rainfall and for beauty.
03. More different types
04.
05. There is a strip welded inside the elbow pipe. At the top of the hole.
06. Welded shield fixing system. No, this is not a bottle of Zhatetsky Gus beer, this is gasoline.
07. Stepsons welded on. There was an error in the calculations. It was assumed that the stepchildren would strengthen the pillar from swinging, but they were attached lower than necessary. Further in the photo you will see that they protrude quite a bit from the ground. It would be possible to raise 30-40 cm higher. And now, nevertheless, the pillar sways during the game.
08. The heels are welded to the part that goes underground.
09.
10. Everything is painted
11.
12. Yamka
13. It will stand so for a couple of days and you can continue the part of the pillar, because there was no putty for metal, to putty the seams. The putty was bought in addition, puttied and repainted a little later.
14. Up!
15. Shield assembly.
16. Done!
17. Now the ring is at its lowest height. Even lower than calculated, because one hole is not used (see the vacant thumb screw). Altitude change occurs with the help of one man-power on a stepladder.
18.
19. The village basketball open championship has begun!
Did you have to restrain yourself when you passed the basketball court in order not to throw the ball into the basket? Why hold back? Team sports reliably unite people of any age, religion and social status. And in order to look decent at any moment and on any site, it is enough just not to start training.
Small places for playing streetball can be equipped on sports grounds near the house, and rings can be built at summer cottages for children to play from improvised means. So, how to make a basketball hoop yourself?
Dimensions and materials required
The inner diameter of the basketball hoop is 45 cm;
the height of its upper edge above the playground is 3. 05 m;
ring material - metal bar, plastic pipe, improvised materials;
diameter of a bar or a pipe for a ring — 16-20 mm;
distance from the ring to the shield - 15 cm;
mesh length - 40-45 cm;
mesh material - metal chain, synthetic cord, rope, braid.
Types of basketball hoops
Hoops can be different:
metal with anti-vandal nets made of metal chain;
metal with rope mesh;
plastic with nets of various types of materials;
creative (from the remains of construction, from old furniture, from large plastic containers).
The construction of a ring from a metal bar begins with marking. Since the basket must have an internal diameter of 45 cm, a rod or pipe is selected based on this.
Material length is calculated using the formula:
Bar length = Circle diameter x 3.14 (pi value). We have 45 × 3.14 = 141.3 cm.
Since we need to fasten the ring to the shield, take the length of the rod about 150 cm. You can bend the rod or pipe on the template (wheel), or you can bend it to size, measure the diameter and straighten it with a mallet. The rest of the rod or pipe should be prepared for fastening to the shield using drilled holes and screws.
The ring is ready. Now you can make a grid to it. If it is assumed that the ring will hang in the adjacent territory of an apartment block, then it is better to make the grid anti-vandal, using a metal chain. The mesh is attached to the ring using 12 lugs or a smaller diameter rod welded on the bottom of the main ring.
Rope, braid, twine net can be woven by yourself. To do this, the material 20 m long, from which the mesh is prepared, is cut into segments of 160 cm. If it is supposed to hang the mesh on 12 loops, then 12 segments are prepared.
When hanging pieces of rope on the ring, each section is picked up by a marine knot. The next row of weaving begins with knots connected by a series of hanging ends. So you need to weave 4-5 rows. For the beauty and accuracy of the product, you can use a template, placing it under the knots to be connected. The lower ends of the rope should be melted to prevent fraying.
Standard basketball hoop height and size But this is not necessary if you just want to throw the ball into the basket. Now it is possible to purchase ready-made equipment even for placement in an apartment or office. The size of the basketball hoop, although it has standard values, is only for official competitions. In everyday life, everyone can choose the size of the basket and the ball at will.
The history of basketball
Experts believe that this is perhaps the only game about which it is known for certain who invented it and when. It happened in 1891 in Springfield, USA. Dr. D. Naismith, a teacher at the Christian Youth Association's Learning Center, decided to come up with an outdoor indoor team ball game to replace American football. According to another version, he wanted to revive gymnastics in this way.
One way or another, they were offered rules according to which the players of the two teams had to throw the ball into baskets suspended at a height. Each team had its own zone and basket. In the hall, D. Naismith simply hung them on the balconies. The players had to hit the opponent's basket with the ball and protect their own from their hits. Whoever hits the target more times in the allotted time wins. There were rules for dribbling, penalties for violating the rules were stipulated. In those days, the size of the basketball hoop was not strictly regulated. Fruit baskets were used for these purposes. And the balls were then far from ideal shape. In order not to get them every time, they took out the bottom of the baskets.
Development of the game
Trial competitions showed that the rules needed to be changed. The spectators on the balconies, where the baskets hung, prevented the ball from getting inside. So the shields were born. Initially, they served as protection from the fans, but already the first games showed that it was even more interesting that way. The ball could hit the ring after a successful rebound from the shield. This added spice to the game and made it possible for teams to change tactics.
The size and height of the basketball hoop did not change significantly over time. At 1893 year wicker baskets for fruit ceased to be used in tournaments. To replace them, rings made of a metal rod were invented. A net was attached to it so that there would be no disputes about a successful hit. With it, it was better to see when the ball hit the target. In 1894, unified rules for basketball were proposed. The game was liked and quickly spread to Japan and China, South America and Europe. Basketball first appeared in Russia in 1906. In the twenties of the last century, it began to be introduced as a discipline in military and sports schools.
Professionals and amateurs
For an athlete who has linked his career with the game, it matters what size basketball hoop is used in training. The skills of determining the position for the throw, its strength, trajectory have been practiced for years. In the US, where basketball quickly moved from amateur to professional, good players became highly valued. The cost of individual contracts reached one dollar per minute of play. At that time, it was very good earnings. They encouraged the players to train hard to show good ball control on the court and high performance in shots on the basket.
The difference in the level of professional basketball players in the US and other countries where the game is not so popular was felt. For a long time, the Olympic Committee banned players from the NBA from participating in their tournaments. And when this restriction was lifted, the US team confidently defeated the best team from Croatia at that time. However, the professionals were still put to shame, because they were so sure of their advantage that they promised to win by 50 points. That final match of the Olympic Games ended with a score of 117:85. The victory of the professionals was obvious, but the "amateurs" gave a serious rebuff and managed to lose only 32 points.
Basketball hoop: dimensions, diameter
Back in 1893, when thoughtful rules of the game were proposed, it was decided to standardize the inventory according to uniform standards. Then the rings began to be made of metal, equipped with a mesh, securely and securely fastened to the shield and supporting structures at a certain height from the site. What are these standards?
Today, the playground should have dimensions of 28×15 m. The height of the enclosed space (ceiling) is at least 7 meters. The shield (bottom edge) is attached at a height of 290 cm from the floor. It has dimensions of 180x105 cm. The basket (a metal ring with a mesh) is attached to the shield at a height of 305 cm (respectively, 15 cm above the lower edge of the shield). The diameter of the ring should be within 45-45.7 cm. For its manufacture, a steel bar 16-20 mm in diameter is used.
The game ball varies in circumference and weight and is respectively: for men - 74.9-78 cm, 567-650 g, and for women - 72. 4-73.7 cm, 510-567 g. FIBA controls and approves playground equipment and inventory. Balls for official competitions are made of leather. Air pressure should ensure that the ball bounces to a height of 1.2-1.4 m after it falls from a height of 1.8 m.
Net
Any sports equipment must be injury-proof. The verified size of the basketball hoop also provides for the use of a standard size net with it and an acceptable configuration. It should be fastened in such a way as to minimize the possibility of pinching fingers during the game.
Net length standard is 40-45 cm. 12 loops are available for attaching to the metal bar of the basket. For the manufacture of the mesh, a white cord of a certain stiffness is used. The weave configuration does not allow its edges to roll over during ring play or entanglement. The ball cannot get stuck and at the same time must pass with some delay, making it possible to capture the moment it hit the basket.
Design Features
It is not enough to use only a standard size basketball hoop for training. The height of its placement above the ground is no less important. The dimensions of the shield and the applied boundary lines (5 cm - width) marking the quadrangle (45 cm by 59 cm) behind the basket are also important. The material for the shields is often polycarbonate or tempered glass. Its surface should be smooth and even.
The shield is fixed rigidly to the supporting base, with the plane perpendicular to the floor. The structure must not move during the game during throws and contacts. The lower edge and ends of the shield plane to a height of 35 cm, as well as all supporting structures, are upholstered with soft material, which excludes injury. In general-purpose sports halls, mobile racks with a basket are now increasingly used. They can be quickly installed and dismantled if necessary. In basketball halls, backboards are attached to the ceiling or walls. They can also be hung on special stretch marks.
The basket can be attached rigidly or with a shock absorber. In this case, the plane of the ring should not bend more than 30 degrees and immediately return to its original position. Regardless of the method of fastening, the design must absorb 35-50% of the load of the player's weight on contact.
Do-it-yourself basketball hoop: dimensions
Playgrounds for training athletes and competitions are equipped by the relevant organizations according to existing standards. To be able to practice at home, you can purchase a separate board with a basket and hang it in a suitable place or install a ready-made and fully equipped rack. But you can do everything yourself.
If there are plans to engage in this sport in the future, then when making the backboard, it is desirable to maintain the standard size of a basketball hoop. It will be problematic to bend and weld a steel bar with a diameter of 16 mm without suitable equipment and locksmith skills. But you can adapt an old aluminum hoop for rotation for these purposes. It is cut, bent to the desired diameter and secured with an outer insert.
To change rim height simply slide pin to remove, then raise or lower rim height by pushing or pulling adjustment handle up or down. Replace pin at any desired height setting.
The rim will stay at the height when you stop pushing.
The process of reducing the basketball hoop depends totally on the system you have installed. Needless to say, there are fixed height model basketball systems in which you may be unable to lower the hoop.
So, you don't need an additional broom or pole to raise or lower the system. If you want to lower the hoop, you just need to push the handle upwards, and it's done.
It requires you to do nothing but hold the handle and move it up or down using the trigger to get the position. To lower the hoop in this mechanism, you need to raise the handle, and it's done.
And the best part is that almost each and every model in this category are manufactured with a Screw Jack Lifting Mechanism.
You need to slide the pin and move the handle upward to lower these basketball systems' hoops.
In both mechanisms, you have to rotate the handle as referred to in the manual to lower the basketball hoops.
2 types of systems are mostly found in the gym.
Basketball backboard dimensions and markings 
Then you should take the prepared rope and cut it into 20-22 identical segments. At the same time, the length of each should be 2.5 - 3 times greater than the planned length of the mesh hanging. 
05 meters. This size will allow players to make more accurate and varied throws. 
The width of the stripes of the square should be 5 centimeters. 
05 m above the surface of the site at an equal distance from the vertical edges of the shield. 
Now it needs to be firmly fixed. To do this, you will need 4 large bolts that can withstand a load of 30 kg, and drill four holes in the wall or any other place where the basketball backboard will be mounted. 
The weight of the ball (if you do not go into the definition of physical values) during contact with the ring increases many times, even when thrown from an average distance. 
Plastic plastic is different, because the one that is used in the gym is very expensive, another different lottery ... will stand it - will not stand it. But a wooden board, it is a material that has stood the test of time and history. It is known that the official dimensions of the basketball backboard are as follows - a width of 1 meter 80 centimeters and a height of 1 meter 5 centimeters. 
How the game "basketball" appeared, and what is a basketball backboard with a ring as a necessary element of this popular game, we will learn in this article. 
It was supposed to develop coordination of movements in teenagers and at the same time be interesting. 
It is allowed to produce such shields from other materials, but in this case they must be painted white and comply with other requirements for such sports equipment. 
Two shields are installed opposite each other from different ends of the field, the material is impact-resistant (as an option, tempered glass, acrylic, wood). Lines are drawn on a smooth surface. Models of basketball backboards with a net that are not intended for stationary installation are equipped with the same mounting elements as in the brackets for hanging punching bags. This method makes basketball backboards able to withstand a lot of weight and securely fixes them. 
In the summer, you can throw the ball with pleasure, feeling like Michael Jordan for a moment. This game is available to everyone: both children and adults. The benefits of such a seemingly simple exercise are incredible! 
The length of each is 2.5–3 times the planned length of the net hanging. 
Diagonals that are not in the drawing (green) have also been cancelled. We decided that the rigidity of the wooden shield and metal fasteners would be enough not to "walk". 
At the top of the hole. 
05 m; 
You can bend the rod or pipe on the template (wheel), or you can bend it to size, measure the diameter and straighten it with a mallet. The rest of the rod or pipe should be prepared for fastening to the shield using drilled holes and screws. 
For the beauty and accuracy of the product, you can use a template, placing it under the knots to be connected. The lower ends of the rope should be melted to prevent fraying. 
The ball could hit the ring after a successful rebound from the shield. This added spice to the game and made it possible for teams to change tactics. 
In the US, where basketball quickly moved from amateur to professional, good players became highly valued. The cost of individual contracts reached one dollar per minute of play. At that time, it was very good earnings. They encouraged the players to train hard to show good ball control on the court and high performance in shots on the basket. 
4-73.7 cm, 510-567 g. FIBA controls and approves playground equipment and inventory. Balls for official competitions are made of leather. Air pressure should ensure that the ball bounces to a height of 1.2-1.4 m after it falls from a height of 1.8 m. 
The height of its placement above the ground is no less important. The dimensions of the shield and the applied boundary lines (5 cm - width) marking the quadrangle (45 cm by 59 cm) behind the basket are also important. The material for the shields is often polycarbonate or tempered glass. Its surface should be smooth and even. 
In this case, the plane of the ring should not bend more than 30 degrees and immediately return to its original position. Regardless of the method of fastening, the design must absorb 35-50% of the load of the player's weight on contact. 
